3
8
(2) Press SEL button and hold for more than 2 seconds to turn on TA SEEK/TA ALARM
mode, then press SEL button shortly and repeatedly to select PI SOUND/PI MUTE,
RETUNE L/RETUNE S, MASK DPI/MASK ALL, BEEP 2ND/BEEP ALL/BEEP OFF, SEEK1
/SEEK2(in RADIO mode), DSP OFF/FLAT/POP M/CLASSICS/ROCK, LOUD OFF/LOUD
ON, SUBW OFF/ON(with subwoofer output), STEREO/MONO(in FM mode), DX/LOCAL
(in FM mode), VOL LAST/VOL ADJ(When it is in VOL ADJ mode, the next mode will be
A-VOL after VOL ADJ mode, then you can adjust the volume level. The minimum value of
the volume level you can set is 10) and ESP 6/ESP 25 in the sequence and circulation. After
selecting the desired mode, rotate VOL knob to select one setup item of the desired mode.
1) TA SEEK/TA ALARM:
TA SEEK mode: when newly tuned station does not receive TP information for 5 seconds,
the radio retunes to next station which has not the same station(PI) as the last station, but
has the TP information.
When TP information gets lost at the current station for retune time which is set by
RETUNE SHORT(60 seconds) or RETUNE LONG(90 seconds), the radio start to retune
to next same PI station. When same PI station does not catch in 1 cyclic search, the radio
retunes to next station with TP information.
TA ALARM mode: when this mode is selected, any automatic retune mode is not activated.
Only double beep sound(ALARM) is out-put.
When newly tuned station does not have TP information for 5 seconds, beeps come out.
When TP information gets lost at the current station for retune time, the beep sound is
out-putted.
When newly tuned station has not RDS signal, PI SEEK is suppressed somewhat.
2) PI SOUND/ PI MUTE:
PI SOUND mode: if a car cruises that critical area back and forth, an oscillation phenome
-non can be occurred, because the different PI code can be receive from a same AF. when
the different PI sound (DIP) is heard once in a while, the different PI sound will be heard
for less than 1 second.
PI MUTE mode: under above same situation, a mute sound will be heard for less than 1
second.
3) RETUNE L / RETUNE S:
The initial time of automatic TA search or PI SEARCH mode is selected.
When PI information is not caught for retune time , the radio start to retune to next same
PI station.
When same PI station does not catch 1 cyclic search, the radio goes to last station and
waits for 4-5 minute until PI code is received.
RETUNE L mode: selected as 90 seconds.
RETUNE S mode: selected as 60 seconds.
4) MASK DPI/MASK ALL:
MASK DPI mode: masked only the AF which has different PI.
MASK ALL mode: masked the AF which has different PI and NO RDS signal with high
field strength.
5) BEEP 2ND/BEEP ALL/BEEP OFF:
BEEP 2ND mode: the beep is only generated when an allotted double key is pressed
long(1second).
BEEP ALL mode: the beep is generated when every key is pressed(except power and
release buttons).
BEEP OFF mode: the beep is disabled.
6) SEEK1/SEEK2:
SEEK1: press UP/DOWN button and hold to seek up or down for the strong signal station.
And then stop seek when received the strong signal station.
SEEK2: press UP/DOWN button and hold to seek up or down for the strong signal station. And
do not stop seek when received the strong signal station. After release it and then
received the strong signal station, the seek will stop.
Ò É
Ä Ñ
½ â
³ ý
CARE FOR USING CD'S:
About CD-R/CD-R/W discs:
In addition to commercially-recorded audio CD's, this unit can play CD-R and
CD-R/W discs. In come cases, particularly when recorded on older CD burners,
some CD-R and CD-R/W discs may not play. Also, whenever you are recording
a CD for playback in this receiver, it is recommended that you record at 24x or
slower speed for CD-R and 4x or slower for CD-R/W to achieve higher signal
quality and better playback performance.
Do not attach any sticker or adhesive tape on the disc.
Handle the disc by its edge to keep the disc clean and do not touch the surface.
. Insert a
disc with labeled surface up, or it will damage the unit.
3. Do not expose the disc to direct sunlight or nearby heat sources such as heating
vents, caliduct which can cause the disc to warp.
Do not leave disc in a car if it is parked in direct sunlight as that will lead to a
considerable rise in the temperature inside the car.
4. Do not use any secondhand or rented disc, usually, there is glue on the surface
of those discs, it will stop the unit working and damage it.
5. Always store the disc in its case for protection. Scratched up discs will produce
poor sound performance and cause CD player to skip.
6. In raining day or wet area, the moisture may form on the disc or the optical parts,
The playback may not be possible. If moisture forms on the disc, wipe it off with
a soft cloth. If moisture forms on the optical parts of the unit, allow the unit to sit
for about one hour with power on.
7. Do not use solvents such as benzine or thinners. Commercially available
cleaners or anti-static spray will damage the unit.
1. To keep the disc clean:
Before playing a disc, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc outwards from the disc center.
2. When one has already been inserted. Doing so may damage the unit