AJA Io IP Скачать руководство пользователя страница 27

Страница: 27 / 86

Io IP Transport, Capture, Display v16.2r1 27 www.aja.com

Control Panel Operation in ST 2022-6 Mode

Control Screen

The Io IP can be controlled by various software applications running on a host

computer. The Control screen is where you select how the Io IP directs video and

is used by application software. This screen also provides control for configuring

output timing with regard to external reference video and horizontal/vertical

delay. The top of the Control Screen shows the currently selected AJA device if

more than one is available in your system.

Default Output

This is where you select what the Io IP will output as a default when no

application has control of the board, such as when the Mac Finder or Windows

Navigation Pane is active. Since Io IP can be controlled by software applications

as well as its own control panel, the output can change dynamically. When you

select many video applications, they will take control of the Io IP inputs and

outputs. However, when an application that doesn’t take control is active, these

settings determine what Io IP will output.

Input Passthrough

This selection directs Io IP to route video from its selected input through the

device for processing and output.

Test Pattern

This selection directs the Io IP to output a choice of preset pattern when no other

application is using the Io IP. You can choose from:

• Black, Color Bars (75% or 100%), Ramp, Multiburst, Line Sweep, Multi Pattern,

or Flat Field, Check Field, White, Border, Linear Ramp, Slant Ramp, Zone Plate,

and Color Quadrant

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды