AJA Io IP Скачать руководство пользователя страница 13

Страница: 13 / 86

Io IP Transport, Capture, Display v16.2r1 13 www.aja.com

Power LED

The power LED lights up yellow when power is provided via the power supply.

Once a Thunderbolt 3 connection is made, and the host is in an active state, the

light turns green.

Rear Panel Connectors

Figure 2. Io IP Rear Panel

Thunderbolt 3

Ports (2)

SFP Cage 1

SFP Cage 2

Balanced Audio In/Out

DB-25F (8-Ch)

4-Pin XLR

DC Power Input

HDMI

Output

HD/SD-SDI

Monitor Out BNC

Reference or

LTC Input

Thunderbolt 3

The Io IP provides the third-generation Thunderbolt 3 (USB-C) ports to support

increased bandwidth between host computer and I/O device. Two ports are

provided for daisy-chained network configurations.

SFP Cages and Modules

Two SFP+ cages are provided to connect two separate 10 Gigabit Ethernet Links.

Both links are bi-directional. Inputs and outputs for most uses will be set up over

the same link if bandwidth allows it.
For a list of SFP+ modules tested by AJA, see

"Appendix A Specifications" on page

Dedicated SDI HD/SD Output

One BNC connector is provided for full-time, real-time output of 2K/HD/SD video.

When running ST 2110 firmware, ANC data is included in the SDI monitor output.

HDMI Output

A full-size HDMI connector on the Io IP endplate provides HDMI 2.0 capability.

HDMI also supports multi-channel embedded audio (8 channels). HDCP is not

supported on the output. HDMI Output also supports HDR (HDR10 and HLG).

Reference Video

When in SMPTE 2022-6 mode, Io IP can lock to reference analog or tri-level input,

or the incoming SMPTE 2022-6 stream.
For analog reference, a single BNC on the Io IP endplate allows you to synchronize

Io IP outputs to your house analog or tri-level reference video signal (or black

burst). If you have a sync generator or central piece of video equipment to use

for synchronizing other video equipment in your studio, connect its output here.

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды