AJ 31019, Руководство по эксплуатации

Страница: 103 / 118

3 | 01252 359760 • ajproducts.co.uk
4. GUIDE TO SAFETY OPERATION
4.1 Disconnect all power to the pallet truck with scale before installing,
servicing, cleaning or removing the fuse. Failure to do so could result in
bodily harm and/or property damage.
4.2 To pull the truck, always move the control handle into the drive position.
This makes the draw-bar easier to move and depressurizes the pump
section of the hydraulics. This preserves the hydraulic seals and the valve
components. A long service life can be expected.
4.3 Operator should read all warning signs and instructions here and on the
pallet truck before using this truck with scale.
4.4
Do not operate a pallet truck with scale unless you are familiar with it and
have been trained or authorized to do so.
4.5 Do not operate a pallet truck unless you have checked its condition. Give
special attention to the wheels, the draw-bar unit, the fork unit, the lever
plate, etc.
4.6
Do not use on a slopping ground.
4.7 Do not take up any people on the pallet truck when moving.
4.8 The operator had better take on gloves for labor protecting.
4.9 When the goods have been transported, all people should be away from
the forks for 600mm.
4.10
Do not load goods like fig. 5/B, the barycenter of the goods should be on
the midline of pallet truck with scale.
4.11 Do not load over maximum capacity.
4.12 At others special condition or place, the operator should be carefully to
operate the pallet truck.
5. TROUblES ShOOTING
Trouble Clause Fixing Methods
The forks can not be up
the max. height.
-The hydraulic oil is not
enough.
-Pour in the oil.
The forks can not be
lifted up.
-Without hydraulic oil.
-The oil has impurities.
-The nut (G104) is too
hig, keep the pumping
valve open.
-Air come into the
hydraulic oil.
-Fill in the oil.
-Change the oil.
-Adjust the nut (G104) or
screw (318) (see item
2.4).
-Banish the air (see item
3.2).
The forks can not be
descended.
-The piston rod (328) or
pump body (322B) is
deformed resulting from
partial loading slanting
to one side or over-
loading.
-The fork was kept in the
high position for long
time with piston rod
bared to arise in rusting
and jamming of the rod.
-The adjusting nut (G104)
or screw (318) is not in
correct position.
-Replace the piston rod
(328) or pump body
(322B).
-Keeping the fork in the
lowest position if not
using, and pay more
attention to lubricate
the rod.
-Adjust the nut (G104) or
screw (318) (see item
2.3).
Leaks -Sealing parts worn or
damaged.
-Some part cracked or
worn into small.
-Replace with the new one.
-Replace with the new one.
The fork descends
without the release valve
worked.
-The impurities in the oil
cause the release valve to
be unable to close tight.
-Some parts of hydraulic
system is cracked or
bored.
-Air come into the oil.
-Sealing parts worn or
damaged.
-The adjusting nut (G104)
or screw (318) is not in
the correct position.
-Replace with new oil.
-Inspect and replace the
waste parts.
-Banish the air. (see item
3.2)
-Replace with the new
one.
-Adjusting the nut (G104)
or screw (318). (See
item 2.2)
The result of scale is
incorrect
-The bolts (G225B)
scrape the platform
(G226B)
-The platform scrapes the
fork (G201B)
-Adjust the bolts (G225B)
- Face lifting the platform.
Nothing is displayed by
the terminal.
- The battery power is too
lower.
- Replace with new one
Appear error cods:
E1,E2,E3...
- See METTLER TOLEDO
”IND221 & IND226
Industry Terminal User/
Service Manual”.
NOTE: DO NOT ATTEMP TO REPAIR THE PALLET TRUCK UNLESS YOU ARE
TRAINED AND AUTHORIZED TO DO SO.
6. WEIGhING OPERATION
6.1
Preparation: Put the control lever in the LOWER position and lower the
truck to lowest position.
6.2 Press the “Print” Key until the backlight on. After the indicator being
checked by itself display “0Kg”.
6.3 Weighing method for gross weight: Put the forks under pallet and judge by
eyes it will be balanced load. Put the control handle in the Lower position,
pump the handle to make the fork be raised until you can make sure the
pallet leave ground. The stable reading of the indictor is the gross weight
of the goods (total weight of the pallet and the goods).
6.4 Net weight weighing method: To weigh the goods packed in the same
type standard pallet, please operate as following:
6.4.1 Weigh single standard pallet, for example: weight of pallet: 40Kg.
6.4.2 Press the key of “TARE”, then the indicator display “0kg”.
6.4.3 Remove the pallet from the fork, then the indicator display “-40kg”.
6.4.4 Weigh the palletized goods according the method of 6.3, the stable
reading of the indicator is the net weigh of the goods.
6.5 The Switch of kilogram and pound. When the reading of indicator is in unit
of kilogram, press the key of “FUNCTION”, the unit of reading switch
to pound. Press the key of “FUNCTION” again, the unit of reading switch
to kilogram again.
6.6
Turn off the Indicator: When the Indicator works normally, press the key
of “PRINT” until the Indicator display “OFF”. Loosen the key will turn off the
Indicator.