background image

15

MAINTENANCE

CHECKING THE OIL LEVEL (DAILY)

1. Make sure that the oil level is half 

way up the oil sightglass.

2. If not, remove the oil breather cap 

and add oil to the reservoir.

3. Only use SAE30 compressor oil, 

available from your local dealer.

DRAIN THE RESERVOIR (DAILY)

After use, always open the drain 
valve to make sure that any 
condensate is drained off.

CLEAN THE AIR FILTER (MONTHLY)

The air filter must be examined monthly, more often in dusty conditions,

1. Remove the filter cover from the 

filter.

2. Remove the sponge filter.

3. Use a soft brush to clean the 

sponge and the filter cover.

• If necessary, the filter can be 

carefully cleaned in warm 
soapy water.

• Rinse and let the filter dry 

completely before refitting.

4. Make sure that the filter and filter cover are replaced into position.

• If the filter is damaged, you must replace it.

CLEANING & STORAGE

Keep the compressor free of dirt and dust as far as possible. Wipe with a clean 
cloth or blow it down with compressed air at low pressure. If cleaning is 
required, use a damp cloth and some soft soap. Do not use cleaning agents 
or solvents as these may be aggressive to the plastic parts. 

Always disconnect the hose and any air tools from the compressor before 
cleaning or storage. Store the compressor in a dry location. Always store 
upright.

Содержание 1499510





















Отзывы: