AirLive SNMP-FSH2602MG V2 Скачать руководство пользователя страница 74

Страница: 74 / 139

5. Console Management in SNMP-FSH2602MG v2

AirLive SNMP-FSH2602MG v2 User’s Manual

FC:

enable or disable

Flow control

function (Flow control for full duplex link mode).

BP:

enable or disable

Back Pressure

function (Backpressure for half duplex mode).

Bandwidth In/Out:

per port packet transmission rate control. Per level is 100Kbps. It

supports individual control method of TX and RX.

Priority:

set port to high or low priority.

10.

Security:

enable or disable port security function.

11. Select the

<Save>

Trunk Configuration

You can configure port trunk group.
1. Select

<Edit>

2. Using “

Tab

” key move to the port that want to be added into trunk group.

3. Using “

Space

” key to mark the port as “

＊

”.

4. Using

Tab

key move to “

Trunk #

” (ex. Trunk 1, Trunk 2…) to change the Trunk # value

to “

Static

”.

5. Save the configuration by selecting

<Save>

Содержание SNMP-FSH2602MG V2












































































































































Результаты поиска

Содержание SNMP-FSH2602MG V2

Отзывы:

Бренды по названию

Популярные бренды

AirLive SNMP-FSH2602MG V2, Руководство пользователя

Результаты поиска

Содержание SNMP-FSH2602MG V2

Отзывы:

Бренды по названию

Популярные бренды