manualshive.com logo in svg

AirLive SNMP-FSH2602MG V2, Руководство пользователя

Поделиться
Скачать
AirLive SNMP-FSH2602MG V2 Скачать руководство пользователя страница 13

2. Installing the SNMP-FSH2602MG v2 

 

 
AirLive SNMP-FSH2602MG v2 User’s Manual 

8

 

 

Note:

 For proper ventilation, allow about at least 4 inches (10 cm) of clearance on the 

front and 3.4 inches (8 cm) on the back of the Switch. This is especially important for 
enclosed rack installation. 

 

2.5.3 Power On

 

 
Connect the power cord to the power socket on the rear panel of the SNMP-FSH2602MG 
v2. The other side of power cord connects to the power outlet. The internal power supply of 
the SNMP-FSH2602MG v2 works with voltage range of AC in the 100-240VAC, frequency 
50~60Hz. Check the power indicator on the front panel to see if power is properly supplied. 
 
 

2.6 LED  Table 

The LED Indicators gives real-time information of systematic operation status. The 
following table provides descriptions of LED status and their meaning. 

 

 

LED 

Status

 

Description

 

Green

 

Power On

 

Power

 

Off 

Power is not connected

 

Содержание SNMP-FSH2602MG V2












































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды