Airflow 90000068 Скачать руководство пользователя

Страница: 15 / 27

Electrical installation may be carried out only by a person having the required electrotechnical
qualification.

Installation scheme when using the RD regulation:

Installation scheme when using the DC regulation:

5.13.

Installing mixing valve of hot water air heater

During the mechanical installation and connection of the mixing valve of the hot water air heater follow
the manual supplied with this optional accessory.

5.14.

Installing shut-off dampers e1, i1

During the mechanical installation and connection of the servo drive of shut-off dampers follow the
manual supplied with this optional accessory.

5.15.

Installing flexible flanges

During the mechanical installation of flexible flanges follow the manual supplied with this optional
accessory.

5.16.

Installing and connecting water chiller to the cool source



During the mechanical installation of the water chiller follow the manual supplied with this optional
accessory.

Servo drive R-HW of the mixing valve LM24A-SR
Cable: 4Ox1,5 (Germany NYM-O 4x1,5)

Temperature sensor TA placed behind the heating coil
Cable: SYKFY 2x2x0,5 (Germany JYSTY 2x2x0,6)

brown

black

blue

brown

white

green

brown

blue

black

Servo drive R-HW of the mixing valve LM24A-SR
Cable: 4Ox1,5 (Germany NYM-O 4x1,5)

Temperature sensor TA placed behind the heating coil
Cable: SYKFY 2x2x0,5 (Germany JYSTY 2x2x0,6)

Содержание 90000068




























Результаты поиска

Содержание 90000068

Отзывы:

Похожие инструкции для 90000068

Бренды по названию

Популярные бренды

Airflow 90000068, Инструкция по установке, использованию и техническому обслуживанию

Результаты поиска

Содержание 90000068

Отзывы:

Похожие инструкции для 90000068

Бренды по названию

Популярные бренды