Aircraft in Miniature Limited Historic Wings Fokker Spin 1912 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 10

Aircraft in Miniature Limited Historic Wings Fokker Spin 1912 Скачать руководство пользователя страница 5

Figure 4

A Remove the left and right wings and the front and rear spars from the fret and

remove any burrs from the attachment tags.

B Check their orientation, then twist all the ribs on each wing through 90°.
C Use the spar fold template and put a fold in each spar to give 10° sweepback to

the wings.

D Make the rib/wing structure into a parallelogram to suit the sweepback.

Engage the slots in the front and rear spars in the slots in the ribs of the right
wing then bond the wing spars in place.

Note - Four ribs on each wing have a bracing rod below that rib, and the spars

go between the ribs and the bracing rods.

E Put the rear spar between the front and rear landing gear struts (below the

fuselage) . Engage the slots in the front and rear spars in the slots in the ribs of
the left wing then bond the wing spars to the ribs of the left wing.

F Attach the spars to the front of each landing gear strut.

Note - There is a small lug on each landing gear strut to give the correct angle

of incidence for the wings. The rear spar is lower than the front spar.

4 WING ASSEMBLY

(see Figure 5)

CONTROL

COLUMN

CONTROL

WHEEL

SEAT

TAILPLANE

SPAR

RUDDER

ARMS

UPPER FIN

LOWER FIN

UPPER AFT

PYLON

FUEL TANK

PYLON

UPPER AFT

PYLON

TAIL SKID

WHEELS

AXLE FROM WIRE

«
...
3
4
5
6
7
...
»

Содержание Historic Wings Fokker Spin 1912











Отзывы:

Нет отзывов