The FOLLOW ME function enables the
remote control to measure the temper-
ature at its current location. When using
AUTO, COOL, or HEAT functions,
measuring ambient temperature from
the remote control (instead of from the
indoor unit itself) will enable the air
conditioner to optimize the temperature
around you and ensure maximum comfort.
1. Press
FOLLOW ME
button to activate
function. The remote control will send
temperature signal to the indoor unit
every three minutes.
2. Press
FOLLOW ME
button again to
turn off this function.
The TURBO function makes the unit work
extra hard to reach your present temperature
in the shortest amount of time possible.
When you press the
TURBO
button in
COOL mode, the unit will blow cool air
with strongest wind setting to ump-start
the cooling process.
When you press the
TURBO
button in
HEAT mode, for units with Electric heat
elements, the Electric Heater will activate
and ump-start the heating process.
Airborne bacteria can grow in the
moisture that condenses around heat
exchangers in the unit. With regular use,
most of this moisture is evaporated from
the unit. By pressing the
SELF CLEAN
button, your unit will clean itself automa-
tically. After that, the unit will turn off
automatically. Pressing the
SELF CLEAN
button mid-cycle will cancel the operation
and turn off the unit.
ou can use
SELF CLEAN
as often as
you like.
Note:
ou can only activate this function
in COOL or DR mode.
FOLLOW ME unction
SHORTCUT unction
SWING unction
ECO unction
SELF CLEAN unction
TURBO unction
SLEEP Function
The SLEEP function is used to decrease
energy use while you sleep (and don t need
the same temperature settings to stay
comfortable). This function can only be
activated via remote control.
Note:
The SLEEP function is not available
in FAN or DR mode.
,
Used to restore the current settings or
resume previous settings.
Push this button when remote controller is
on, the system will automatically revert
back to the previous settings including
operating mode, setting temperature, fan
speed level and sleep feature (if activated).
If pushing more than 2 seconds, the
system will automatically restore the
current operation settings including
operating mode, setting temperature, fan
speed level and sleep feature(if activated ).
Swin Button
DIRECT Button
(not applicable to model RG57 7(B)BGEF)
Used to set the desired up/down air flow
direction. The louver changes 6 degree in
angle for each press.
Used to stop or start horizontal louver auto
swing feature.
o To se T e
ance Functions
o To se T e
ance Functions
ON/OFF
ON/OFF
TEMP
TEMP
TIMER
ON
TIMER
ON
TIMER
OFF
TIMER
OFF
MODE
MODE
FAN
FAN
SLEEP
SLEEP
TURBO
TURBO
CLEAN
CLEAN
LED
LED
FOLLOW
FOLLOW
SWING DIRECT
SWING
DIRECT
SHORT
CUT
Used to enter the energy efficient mode.
Under cooling mode, press this button, the
remote controller will ad ust the temperature
O
automatically to 2 C, fan speed of Auto to
save energy(but only if the set temperature
O
is less than 2 C). If the set temperature is
O
above 2 C , press the ECO button, the fan
speed will change to Auto, the set temperature
will remain unchanged.
NOTE:
Pressing the ECO button, or modifying the
mode or ad usting the set temperature to
O
less than 2 C will stop ECO operation.
Under ECO operation, the set temperature
O
should be 2 C or more. it may result in
insufficient cooling. If you feel uncomfortable,
ust press the ECO button again to stop it.
Model: RG57A7(B)/BGEF
Model: RG57A1(B)/BGEF, RG57B(B)/BGE, RG57K7(B)/BGEF
NOTE:
CLEAN and FOLLOW buttons are
not available for Model
RG57B(B)/BGE
，
DIRECT button is
not available for Model
RG57K7(B)/BGEF.
118
Содержание MDV MOB02-18HFN8-QRD0GW
Страница 2: ... nstrukcja obsługi 2 ...
