AirBench Vertex VP Скачать руководство пользователя страница 12

ACCESSORIES 

Some accessories are only supplied if specified with purchase. 

Filter Pressure Gauges 

A filter pressure gauge is fitted as standard to the front of each VertEx. This indicates performance of the unit 
as a whole, and filter condition. Certain models show a red zone on the filter gauge; when the gauge indicates 

within this zone, filters may be blocked or require cleaning. Turn the VertEx off and inspect the filters. 

Where no red zone is shown, a filter inspection pressure drop will be recorded on the Commissioning 
Certificate. When pressure loss is greater than that shown on the Commissioning Certificate, follow the above 

procedure. 

A high pressure reading may also indicate a blocked surface. Inspect the surface for blockages and clean if 
required. Do not operate VertEx continuously with more than 75% of the face blocked. 

Hours Run Meter 

The meter is not resettable and operates at all times when the speed control or switch is powered. 

Wheels 

Standard industrial rubber wheeled swivel castors are used. The two front wheels are lockable. Lock by 
pressing on the lever and trip by flicking (models and operation vary slightly). Do not attempt to move while 

brakes are on. 

Compressed Air Interlink 

This option ensures the safety of operators by preventing the use of air tools without extraction being 
operational; and reduces energy use by switching off the fan after 5 minutes of non-use. 

4 off series 19 airline connectors are provided to the front or side of the unit and an internal timer fitted, pre-set 
to an agreed value – usually 5 minutes. The control panel is supplied with an additional Red / Green push-
button. 

System control will be as follows: 

Switch main on/off switch to On – system is energized. Airline is switched to operational. 

Press green button – fan starts and runs for 5 minutes. 

Use airline or press green button again – timer is reset for a further 5 minutes. 

Press red button – fan stops, airline stops. 

The timer can be re-set to a different interval; contact the manufacturer for details.

© Copyright AirBench Ltd 2016

Page 

!

 of 

!

12

16

Содержание Vertex VP

















Отзывы: