Air Live SA-102 Скачать руководство пользователя страница 23

Страница: 23 / 24

1. Overview

AirLive SA-102 User Manual

COMMAND_CLASS_SCENE_ACTUATOR_CONF

COMMAND_CLASS_PROTECTION

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

COMMAND_CLASS_MULTI_CHANNEL_V3

COMMAND_CLASS_METER_V3

COMMAND_CLASS_CONFIGURATION

1.7 Troubleshooting

Symptom

Cause of Failure

Recommendation

The Switch not working and
LED off

The Switch is not connect to
the Main power

The Switch break down

Check power connections
Don’t open up the Switch

and send it for repair.

The Switch LED
illuminating, but cannot
control the ON/OFF Switch
of the load attached

Check if the load connect into
the Switch has its own
ON/OFF switch

Set the ON/OFF switch of
the load attached to ON

The Switch LED
illuminating, but the
Detector cannot control the
Switch

Not carry out association
Same frequency interference

Carry out association
Wait for a while to re-try

LED keep flashing, but

cannot control

Overload occurs

Remove the load attached

or check max. load cannot
exceed 7.5A(Resistive load)

Содержание SA-102

























Результаты поиска

Содержание SA-102

Отзывы:

Похожие инструкции для SA-102

Бренды по названию

Популярные бренды

Air Live SA-102, Руководство пользователя

Результаты поиска

Содержание SA-102

Отзывы:

Похожие инструкции для SA-102

Бренды по названию

Популярные бренды