background image

Troubleshooting Guide

LoadLifter 5000 Series

MN-1047

16

PROBLEM

CAUSE

SOLUTION

System won’t maintain pressure 
overnight.

Improperly installed air line, air line has 
holes or cracks.

Leak test the air line connections, the 
threaded connection into the air spring, and all 
fittings in the control system.

Air spring or air line leak. 

Fitting seal or air line is compromised.

Check to make sure air lines are seated in 
connectors. Inspect fittings with soapy water. 
Trim hose or re-seal fitting. Ensure lines are 
cut straight.

Corner won't raise or air leak 
develops.

Look for a kink or fold in the air line. 

Replace any air line that has been kinked.

PROBLEM

CAUSE

SOLUTION

System won’t maintain pressure 
overnight.

Improperly installed air line, air line has 
holes or cracks.

Leak test the air line connections, the 
threaded connection into the air spring, and all 
fittings in the control system.

Air spring or air line leak. 

Fitting seal or air line is compromised.

Check to make sure air lines are seated in 
connectors. Inspect fittings with soapy water. 
Trim hose or re-seal fitting. Ensure lines are 
cut straight.

Corner won't raise or air leak 
develops.

Look for a kink or fold in the air line. 

Replace any air line that has been kinked.

FREQUENTLY ASKED QUESTIONS

Q . Will installing air springs increase the weight ratings of a vehicle?
  No. Adding air springs will not change the weight ratings (GAWR, GCWR and/

or GVWR) of a vehicle. Exceeding the GVWR is dangerous and voids the Air Lift 
warranty.

Q . Is it necessary to keep air in the air springs at all times and how much pressure 

will they need?

  For LoadLifter 5000 standard, Ultimate and Ultimate Plus, the recommended 

minimum air pressure is 5 PSI, but it can safely be run at zero air pressure unladen 
(no load).

Q . Is it necessary to add a compressor system to the air springs?
  No. Air pressure can be adjusted with any type of compressor as long as it can 

produce sufficient pressure to service the springs. Even a bicycle tire pump can be 
used, but it’s a lot of work. 

Q . How long should air springs last?
  If the air springs are properly installed and maintained they can last indefinitely. 
Q . Will raising the vehicle on a hoist for service work damage the air springs?
  No. The vehicle can be lifted on a hoist for short-term service work such as tire 

rotation or oil changes. However, if the vehicle will be on the hoist for a prolonged 
period of time, support the axle with jack stands in order to take the tension off of the 
air springs.

Содержание 57275





















Отзывы: