4
TROUBLESHOOTING cont’d...
Charger LED is
flashing Green.
Vectron
®
Wave will not
start or has lost power.
Vectron
®
Wave is flying
too low.
NOTE:
If normal function of the product is disturbed or
interrupted, strong electro-magnetic interference may
be causing the issue. To reset product, turn it completely
off, then turn it back on. If normal operation does not
resume, move the product to another location and try
again. To ensure normal performance, change the
batteries, as low batteries may not allow full function.
1. Batteries in charger are low.
1. You have not set the motor switch
to “ON”.
2. Charger battery power is low.
3. Batteries (+) or (-) are not correctly
placed inside the battery compartment.
4. Vectron
®
Wave battery is low.
1. The batteries in the charger are drained.
2. Vectron
®
Wave’s battery is low.
3. Hair or debris may be caught in the rotor.
1. Install new batteries in charger.
1. Slide motor switch to “ON”.
2. Replace the charger batteries.
3. Be sure to align the (+) and (-) polarities
with the corresponding markings inside
the battery compartment.
4. Recharge Vectron
®
Wave.
1. Install new batteries in charger.
2. Recharge Vectron
®
Wave.
3. Remove hair or debris.
PROBLEM
SOLUTION
CAUSE
TM
Spin Master Ltd., 450 Front Street West, Toronto,
ON M5V 1B6 Canada
Spin Master, Inc., PMB #10053, 300 International Drive,
Suite 100, Williamsville, NY 14221, USA
Spin Master Toys Far East Limited, Rm #1113, 11/F,
Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsui E.,
Kowloon, HK
North American Consumer Information
Phone: 1-800-622-8339
www.spinmaster.com
®, TM and © 2009 Spin Master Ltd. All rights reserved. Conforms to product safety
standards ASTM F963, EN71 Regulatory Requirements. • Please retain this information
for future reference. • Please remove all packaging materials before giving to children.
• An adult should periodically check this toy to ensure no damage or hazards exist, if
so, remove from use. • Children should be supervised during play. • Keep addresses
and phone numbers for future reference. • The item inside this package may vary from
the photographs and/or illustrations. Subject to one or more U.S. or world patents
under license from Go Wireless Ltd., including U.S. Patent No. 7,147,535 and U.S.
Design Patent No. D534467. MADE IN CHINA.
20019142, 20019143 NEN REV 0
IMPORTANT BATTERY INFORMATION
• Requires 6 x 1.5-V AA alkaline batteries (not included).
• Batteries are small objects.
• Replacement of batteries must be done by adults.
• Follow the polarity (+/-) diagram in the battery compartment.
• Promptly remove dead batteries from the toy.
• Dispose of used batteries properly.
• Remove batteries for prolonged storage
• DO NOT incinerate used batteries.
• DO NOT dispose of batteries in fire, as batteries may explode
or leak.
• DO NOT mix old and new batteries or types of batteries
(i.e. alkaline/standard).
• DO NOT use rechargeable batteries.
• DO NOT recharge non-rechargeable batteries.
• DO NOT short-circuit the supply terminals.
Your Vectron
®
Wave is equipped with a
Lithium Polymer battery.
WARNING:
• Never charge battery unattended.
• Charge battery in isolated area. Keep away from flammable
materials.
• Do not expose to direct sunlight.
• There is a risk of the batteries exploding, overheating, or
igniting. Do not disassemble, modify heat, or short circuit
the batteries. Do not place them in fires or leave them in
hot places.
• Do not drop or subject to strong impacts.
• Do not allow the batteries to get wet.
• Only charge the batteries with the specified Spin Master™
battery charger.
• Only use the batteries in the device specified by
Spin Master™.
• Carefully read the instruction guide, and use the batteries
correctly.
• In the unlikely event of leakage or explosion use sand or a
chemical fire extinguisher for the battery.
• Batteries must be recycled or disposed of properly.
This product complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesirable operation. This equipment has been tested and found to comply with the limits for Class B digital devices
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference to
radio communications. Because this toy generates, uses, and can radiate radio frequency energy, there can be no guarantee that
interference will not occur. If this toy does cause interference to radio or television reception (you can check this by turning the
toy off and on while listening for the interference), one or more of the following measures may be useful: • Reorient or relocate the
receiving antenna • Increase the separation between the toy and the radio or the TV • Consult the dealer or an experienced TV-
radio technician for help.
NOTE:
Changes, adjustments or modifications to this unit, including but not limited to, replacement of any
transmitter component (crystal, semiconductor, etc.) could result in a violation of FCC rules under part 15 and/or 95 and must be
expressly approved by Spin Master Ltd. or they could void the user’s authority to operate the equipment.
This class B digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
