AIR GAP Fluidmaster 6000 Series Скачать руководство пользователя страница 8

WARRANTY

This Fluidmaster product has a limited warranty for a period of 5 years.

For complete warranty details, please visit our website at 
www.fluidmaster.com.

For more information in the UK, contact:

[email protected]
www.fluidmasterUK.com  

Do not use in-cistern drop-in toilet bowl cleaners 

containing bleach or chlorine. 

Use of such products will: 

(1) result in damage to cistern components and may cause 
flooding and property damage and (2) void fluidmaster warranty.

Do not overtighten nuts or cistern/bowl may crack.

 

Always use quality Fluidmaster parts when installing or repairing. 
Fluidmaster will not be responsible or liable for use of 
non-Fluidmaster parts during installation or repair.

It is the responsibility of the installer to ensure work is carried out in accordance with all 
appropriate regulations and guidance.

© 2019 Fluidmaster, inc. ® Registered trademark of Fluidmaster, inc. AirGap™ is a 
trademark of Fluidmaster GB Ltd. Leaflet code: 

LF00296 Rev 2 - 03/01/2020

6000 Series AirGap™ Installation Guide

Warranty & contact details

Содержание Fluidmaster 6000 Series









Отзывы: