background image

Safety Precautions

 

Use extra care when handling gasoline and other flammable fuels. Vapors are 

explosive.

 

(a) Use only approved fuel containers

 

(b) Never remove fuel cap or add fuel when the engine is operating

 

(c) DO NOT SMOKE while operating the machine

 

(d) Never refuel or drain the machine indoors

 

(e) Always use fresh non

-

ethanol fuel. Stale fuel can block the 

carburetor and cause leaks.

 

 

Check that the Operator Presence Control (OPC) and safety switches are 

attached and functioning properly.

 

 

Keep all parts in good working condition and all hardware tightened. 

Replace all worn or damaged decals.

 

 

Do not use near children or pets.

 

 

A damaged cutting device and/or impeller must be replaced. Before use, 

always visually inspect the cutting system to ensure that it is in good 

condition. Do not operate with an out

-

of

-

balance cutting system or impeller.

 

 

 

Operation

 

Do not operate the engine in an enclosed space where exhaust fumes (carbon 

monoxide) can collect. Refuel outdoors only and do not smoke while 

refueling.

 

 

Do not operate the machine under the influence of alcohol or drugs.

 

 

Always pull the starter cord slowly until resistance is felt. Then pull the cord 

rapidly to avoid kickback and prevent hand or arm injury. Ensure that feet 

are away from the cutting system. 

 

 

Operate only in daylight or good artificial light, keeping away from holes 

and hidden hazards.

 

 

Avoid operating the machine in wet grass. Be sure of your footing while 

using this product, especially when backing up. Reduced footing could cause 

slipping.

 

 

Walk, never run when operating the Air Force Hover Mower.

 

Page| 9

 

Содержание F-19 Gen3





























Отзывы: