manualshive.com logo in svg

Agrimate AM-708T, Руководство пользователя

Поделиться
Скачать
Agrimate AM-708T Скачать руководство пользователя страница 16

16

CHEMICAL FILLING

 

 

WARNING

• Before starting the engine, make sure that the spray lever (spray valve) is completely returned. 

Starting with the spray lever still pulled out is dangerous, as chemical fluid may spray out of 

the nozzle as soon as the engine is started.

 

NOTE

•  There is no need to operate the primer when restarting immediately after stopping the engine, 

provided there is fuel left in the fuel tank.

2. Lift the choke lever on the right of the air cleaner until it is in the "closed" position, then open 

the throttle lever on the main unit side about 1/3-1/2 from the "slow" position.

• To start the engine, place the sprayer on an even and stable surface or platform. If the sprayer 

is unstable, the reaction on starting etc. may cause it to fall.

 

!

 

IMPORTANT

• Do not allow the chemical fluid or water in the tank to run out while the engine is running. If 

the engine runs empty it may cause breakage of the spray pump.

•  Make sure that the gear oil is filled until the middle of the check-window. If it is not enough, 

loose the upper bolt and fill the gear oil. (SAE40CC)

1.  Press the primer at the bottom of the carburetor a few times with your finger until the fuel 

starts to flow through the transparent pipe.

(1) bolt 
(2) window
(3) drain bolt

a.  air cleaner
b.  choke lever
c.  close
d.  open
e.  transparent pipe
f.  primer

Содержание AM-708T







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды