background image

3

SAFETY PRECAUTIONS 

MOST ACCIDENTS OCCUR BECAUSE OF NEGLECT OR CARELESSNESS. AVOID NEEDLESS ACCIDENTS 
BY FOLLOWING ALL OF THE SAFETY PRECAUTIONS LISTED BELOW. 

• Machinery should be operated only by those who are responsible and are authorized to do so. Stop the engine, 

lower all equipment, lock the brakes, and remove the ignition key before dis-mounting from the tractor. 

• Never stand between tractor and implement while tractor is being backed to hitch. Loose fitting clothing should 

not be worn, to avoid catching on various parts. 

• Detach implement in area where children normally do not play. 
• When performing adjustments or maintenance on an implement, first lower it to the ground or block it securely at 

a workable height. Only a qualified operator should be permitted on tractor when in operation; no riders allowed. 
Make certain everyone is in the clear before starting tractor or raising or lowering equipment. Operate the tractor 
and implement only while seated in the driver’s seat. Reduce speed when transporting mounted implements to 
avoid bouncing and momentary loss of steering control. 

• A heavy load can cause instability of the tractor. 
• Use extreme care during road travel. Slow down on turns and watch out for bumps. Tractor may need front coun-

ter-weights to counter-balance the weight of the implement. 

• Reduce speed on hillsides or curves so there is no danger of tipping. 
• Avoid driving too close to the edge of ditches or creeks. 
• Do not transport implement on public roads without reflectors and slow moving vehicle emblem in daylight and 

with approved warning lights at night and other periods of poor visibility. 

• Due to the width of some implements, use extra caution on highways, farm roads, and when approaching gates. 
• Always be sure the implement is in the proper position for transport. 
• Keep alert and watch the front as well as the rear when working with the implement. 

TABLE OF RECOMMENDED LUBRICANTS

AGIP

ESSO

IP

SHELL

Gearbox and side 

transmission oil

BLASIA 460

GEAR OIL EP320

OIL 460

OIL 460

Grease

GRMU3

E.P.3

GR3

R3

Add the recommended  
lubricants in the gear box

Add the recommended  
lubricants in the chain case

Содержание BE-FTL












































Отзывы: