background image

2

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded  
operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has 
designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. 

BEFORE YOU START 
Read the safety messages on the implement and shown in your manual.  
Observe the rules of safety and common sense! 

CAREFULLY READ EACH WARNING MESSAGE THAT FOLLOWS. FAILURE TO UNDERSTAND AND OBEY 
A SAFETY WARNING, OR RECOGNIZE A SAFETY HAZARD, COULD RESULT IN AN INJURY OR DEATH  
TO YOU OR OTHERS AROUND YOU. THE OPERATOR IS ULTIMATELY RESPONSIBLE FOR THE SAFETY 
OF HIMSELF, AS WELL AS OTHERS, IN THE OPERATING AREA OF THE ROTARY TILLER. 

UNDERSTAND SIGNAL WORDS 
DANGER and WARNING safety signs are located near the specific hazard.  
CAUTION safety signs list general precautions. 

IMPORTANT SAFETY INFORMATION 
Working with unfamiliar equipment can lead to careless injuries. Read this manual, and the manual for your tractor, 
before assembly or operating, to acquaint yourself with the machines.  
It is the implement owner’s responsibility, if this machine is used by any person other than yourself, is loaned or 
rented, to make certain that the operator, prior to operating: 
1. Reads and understands the operator’s manuals. 
2. Is instructed in safe and proper use. 
3. The use of this equipment is subject to certain hazards which cannot be protected against by mechanical 
    means or product design. 
4. All operators of this equipment must read and understand this entire manual, paying particular attention to  
    safety and operating instructions, prior to using. If there is something in this manual you do not understand,  
    ask your supervisor, or your dealer, to explain it to you. 

Most accidents occur because of neglect or carelessness. Keep all helpers and bystanders twenty-five feet (25’) 
from an operating rotary tiller. Only properly trained people should operate this machine. It is recommended  
the tractor be equipped with a Rollover Protection System (ROPS) and a seat belt that is used. Always stop 
the tractor, set brake, shut off the tractor engine and remove the tractor key, and lower implement to the ground 
before dismounting tractor. Never leave equipment unattended with the tractor running. 

Please remember it is important that you read and heed the safety signs on the rotary tiller, and the safety rules 
set forth. Clean or replace all safety signs if they cannot be clearly read and understood. They are there for your 
safety as well as the safety of others. The safe use of this machine is strictly up to you, the operator.

WARNINGS

Содержание BE-FTL












































Отзывы: