AGP EV160 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 24

AGP EV160 Скачать руководство пользователя страница 5

5

5) SERVICE
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts.

This will ensure that the safety of the power tool is maintained.

Symbols used in this manual

V……..volts
A……..amperes
Hz……hertz
W……..watt
~………alternating current
n

0

………no load speed

min

-1

……..revolutions or reciprocation per minute

.........class II tool

SPECIFIC SAFETY RULES AND SYMBOLS

1. Keep hands away from mixing paddle. Keep both hands on the handles. If both hands
are holding the machine, they cannot be hurt by the paddle.
2. Use only recommended mixing paddle
3. Tighten mixing paddle securely before operation.
4. Secure workpiece properly. Workpiece should be stable and firmly in position to avoid
danger
5. Allow the paddle to come to a complete stop before removing from the medium.
6. Check the paddle for cracks, bent shaft or other damage before operation. Replace
bent, cracked or damaged paddle immediately.
7. Never start the tool with the paddle laying on the floor or any dangerous position.
8. Important: After completing mixing medium, release power switch and wait for coasting
paddle to stop completely before removing from medium or putting the machine down.
9. Never operate the tool in an area with flammable solids, liquids, or gases. Sparks or hot
fragments could cause a fire or explosion.
10. Some mediums can be toxic. Take extra care to prevent inhalation and skin contact
when working with these materials. Request, and follow, any safety information
available from your material supplier.
11. There are certain applications for which this tool was designed.
The manufacturer strongly recommends that this tool NOT be modified and/or used for
any application other than for which it was designed. If you have any questions relative
to its application DO NOT use the tool until you have written the manufacturer and have
been advised.

«
...
3
4
5
6
7
...
»

Содержание EV160

























Отзывы:

Нет отзывов