AGP D-Handle Model Скачать руководство пользователя страница 5

Страница: 5 / 20

ensure these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

Do not force the power tool. Use the correct power tool for your application

. The correct power

tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot

be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or the battery pack from the power
tool before making any adjustments, changing accessories, or storing power tools.

Such

preventive safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool.

Power tools are

dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use.

Many accidents are caused by poorly maintained

power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed.

Use of the

power tool for operations different from those intended could result in a hazardous situation.

5) Service

Have your power tool serviced by a qualified repair person using only identical replacement
parts.

This will ensure that the safety of the power tool is maintained.

Symbols used in this manual

V…….......volts
A…….......amperes
Hz……......hertz
W……......watt
~………....alternating current

………..no load speed

min

-1

….....revolutions or reciprocation

per minute

......warning of general danger

.….class II tool

.…with electrical earth

.......read these instructions

......always wear eye protection

......always wear a dust mask.

.....always wear hearing protection

.....wear safety-approved hard hat

do not dispose of electric tools,
accessories and packaging together
with household waste material

Содержание D-Handle Model





















Результаты поиска

Содержание D-Handle Model

Отзывы:

Бренды по названию

Популярные бренды

AGP D-Handle Model, Оригинальное руководство пользователя

Результаты поиска

Содержание D-Handle Model

Отзывы:

Бренды по названию

Популярные бренды