manualshive.com logo in svg

AGP D-Handle Model, Оригинальное руководство пользователя

Поделиться
Скачать
AGP D-Handle Model Скачать руководство пользователя страница 10

10

THE SWITCH 

The machine has a lockable trigger switch. Squeeze the trigger to start the 
machine. To lock the switch on, press the lock button while holding the 
trigger switch on. To release, squeeze the trigger and release.

WARNING: Never lock the switch on when drilling hand-held. Only 
lock the switch on when mounted to a rig.

OVERLOAD PROTECTION AND OVERHEAT PROTECTION 

Overload Warning System:

When the load reaches overload conditions, the warning system will kick in, lowering the voltage and causing 
the motor to stop. Simply back off the downward pressure to ease the load  and the motor will automatically 
restart.  Then the operator can continue to drill normally.

Overload:

If the excessive load is sustained too long, the motor will shut down completely. In this case, the motor must be 
restarted by turning OFF and then back ON the switch.  When this happens, the motor will very likely be near 
overheating, so it is also a good idea to run the  motor at no load for a few minutes to cool it before continuing.

Overheat Thermal Protection:

If the temperature of the motor gets too high, the thermal protection will shut the motor down. When this  
happens, do not immediately put a load on the motor after restarting. Always run the machine at no load for a  
few minutes to return to a normal operating temperature before continuing. 

CAUTION: The motor will be damaged if it is repeatedly overloaded or overheated. Always cool the 
motor  by running at no load for a few minutes whenever it stops from either overheat or overload.

SAFETY CLUTCH

 This machine is equipped with a mechanical clutch to protect the operator and machine from excessive torque 
forces. When the preset maximum torque level is reached, the clutch will slip. After the clutch slips many times, 
it will become worn and slip at lower and lower torque levels. When this happens, it must be serviced by an 
authorized service provider.   
 

DIAMOND CORE DRILLING 

WARNING: When coring through a floor, the  core  will  fall  down.  Take  precautions  to  avoid injury or 
damage below.

NOTE:  When  drilling  with  a  new  bit  for  the  first time, use less than normal feed  pressure for a time 
until it breaks-in.

1. 

Squeeze the trigger switch to turn the machine on. (For wet drilling and convertible models, press the 

Trigger Switch

Lock Button

Содержание D-Handle Model





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды