background image

7

b)   Check the operation of the lower guard spring. If the guard and the spring are not operating 

properly, they must be serviced before use. 

Lower guard may operate sluggishly due to 

damaged parts, gummy deposits, or a build-up of debris.

c)   Lower guard may be retracted manually only for special cuts such as "plunge cuts" and 

"compound cuts".

 Raise lower guard by retracting handle and as soon as blade enters the material, 

the lower guard must be released. For all other sawing, the lower guard should operate 
automatically.

 

d)   Always observe that the lower guard is covering the blade before placing saw down on bench 

or floor. 

An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is 

in its path. Be aware of the time it takes for the blade to stop after switch is released.

12.  Tighten blade retaining bolt

 and all clamps before operating.

13.  Secure workpiece properly.

 Workpiece should be straight and firmly clamped to avoid  possible  

movement  and pinching as the cut nears completion.

14.  Allow the blade to come to a complete stop

 before removing or securing workpiece, or changing   

workpiece  angle.

15.  Check the inside surfaces

 of the arbor flanges as well as the sides of the blade for freedom from any 

foreign  matter.

16.  Check the blade

 for cracks or other damage before operation. Replace cracked or  damaged blade    

immediately.

17.  Never start the tool

 with the workpiece against the blade.

18.  Allow the motor to achieve full speed

 before cutting.

19.  Important: After completing the cut,

 release power switch and wait for coasting blade to stop 

completely  before putting the saw down.

20.  Never operate

 the tool in an area with flammable solids, liquids, or gases. Sparks from the  commutator/

carbon  brushes could cause a fire or explosion.

21.  There are certain applications for which this tool was designed.

 The manufacturer strongly  

recommends that  this tool NOT be modified and/or used for any application  other than for which  it was 
designed. If you have  any questions relative to its application DO NOT use the tool until  you have 
written the manufacturer and  have been advised

WARNING: Always wear hearing protection with this tool.

1. Intended use

This saw is designed exclusively for the sawing of metal and aluminum. This machine should not be 
used for cutting other materials. Do not use this saw to cut wood. The machine should not be 
converted or modified, e.g. for any other form of use, other than as specified in these operating 
instructions.  The user shall be liable for damages and accidents due to incorrect use. 

Содержание CS320





















Отзывы: