AGL GradoPlane 15 Скачать руководство пользователя страница 5

 

 
 

 

                                                        

   

 

5

 

 

 

INFORMATION TO USER

 

 
This device complies with Part 15 of the FCC Rules.  Operation is subject to the 
following two conditions:  (1) This device may not cause harmful interference, and 
(2) This device must accept any interference received, including interference that 
may cause undesired operation. 
 
This equipment has been tested and found to comply with the limits for Class B 
Digital Device, pursuant to Part 15 of the FCC Rules.  These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation.  This equipment generates and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communications.  However, there is no guarantee 
that interference will not occur in a particular installation.  If this equipment does 
cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures. 
 

• 

Reorient or relocate the receiving antenna 

• 

Increase the separation between the equipment and receiver 

• 

Connect the equipment into an outlet on a circuit different from that to which 
the receiver is connected 

• 

Consult the dealer or an experienced radio/TV technician for help 

 
Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment. 

------------ 

To comply with FCC RF exposure compliance requirements, a separation 
distance of at least 20 cm must be maintained between the antenna of this device 
and all persons. This device must not be co-located or operating in conjunction 
with any other antenna or transmitter. Do not install in a location such that this 
device will be within 20 cm of all persons. 
 
To comply with Industry Canada RF exposure compliance requirements, a 
separation distance of at least 20 cm must be maintained between the antenna of 
this device and all persons. This device must not be co-located or operating in 
conjunction with any other antenna or transmitter. Do not install in a location such 
that this device will be within 20 cm of all persons. For the hand held remote, do 
not transmit while close to the body or while in one’s pocket or holster.  
See Industry Canada RSS 102 for Radio Frequency (RF) Exposure Compliance 
of Radiocommunication Apparatus for exposure compliance. 

Содержание GradoPlane 15

















Отзывы: