Agilent Technologies U2802A Скачать руководство пользователя страница 50

Страница: 50 / 67

Product Specifications

Agilent U2802A 31-Channel Thermocouple Input User’s Guide

General Specifications

POWER CONSUMPTION

±12 VDC, 750 mA maximum

OPERATING ENVIRONMENT

•

Operating temperature from 0 °C to 55 °C

•

Relative humidity at 50% to 85% RH (non-condensing)

•

Altitude up to 2000 meters

STORAGE COMPLIANCE

–40 °C to 70 °C

SAFETY COMPLIANCE

Certified with IEC 61010-1:2001/EN 61010-1:2001 (2nd Edition)

EMC COMPLIANCE

•

IEC 61326-1:2002 / EN 61326-1:1997

1:1998+

2:2001+

3:2003

•

CISPR 11:1990/EN55011:1990 – Group 1, Class A

•

CANADA: ICES-

001: 2004

•

Australia/New Zealand: AS/NZS CISPR

11:2004

SHOCK & VIBRATION

Tested to IEC/EN 60068-2

IO CONNECTOR

•

2 x 68-pin female SCSI connector

•

2 x 34-pin screw terminal block

•

1 x 24 pin screw terminal block

DIMENSIONS (WxDxH)

159.7 mm x 254.2 mm x 40.5 mm

WEIGHT

1.036 KG

WARRANTY

Please refer to

http://www.agilent.com/go/warranty_terms

•

Three years for the product

•

Three months for the product's standard accessories, unless otherwise specified

Please take note that for the product, the warranty does not cover:

•

Damage from contamination

•

Normal wear and tear of mechanical components

•

Manuals

U2802A_UG.book Page 40 Friday, November 25, 2011 10:57 AM

Содержание U2802A




































































Результаты поиска

Содержание U2802A

Отзывы:

Похожие инструкции для U2802A

Бренды по названию

Популярные бренды

Agilent Technologies U2802A, Руководство пользователя

Результаты поиска

Содержание U2802A

Отзывы:

Похожие инструкции для U2802A

Бренды по названию

Популярные бренды