background image

U1253A Quick Start Guide

Performing Resistance, Conductance, and Continuity 
Measurements

Performing Capacitance and Temperature Measurements

1

Set the rotary switch to 

.

2

Connect the red and black test 
leads to input terminals 

Ω

 (red)

 

and 

COM (black)

 

respectively.

3

Probe the test points (by 
shunting the resistor) and read 
the display.

4

Press 

 to scroll through 

audible continuity (

/

), 

conductance (

), and 

resistance tests (

, or 

) as shown.

PRESS SHIFT

PRESS SHIFT

Audible
continuity

Capacitance

1

Set the rotary switch to 

.

2

Connect the red and black test 
leads to input terminals 

 (red)

 

and 

COM (black)

 

respectively.

3

Connect the red test lead to 
the positive terminal of the 
capacitor, and the black test 
lead to the negative terminal.

4

Read the display.

Temperature

1

Set the rotary switch to 

Press  

to 

select 

temperature measurement.

2

Connect the red and black test 
leads to input terminals 

 (red)

 

and 

COM (black)

 

respectively.

3

Plug the thermocouple adapter 
(with the thermocouple probe 
connected to it) into input 
terminals 

TEMP (red)

 and 

COM 

(black)

.

4

Touch the measurement 
surface with the thermocouple 
probe.

5

Read the display.

U1253A QSG.fm  Page 3  Tuesday, September 23, 2008  9:44 AM

Содержание U1253A







Отзывы: