Agilent Technologies G3180B Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 52

background image

24

Installation and Operation Guide

2

Hardware Installation

Connect the Makeup Gas Supply

Connect the makeup gas source to the PCM or Auxiliary Pressure controller.

To supply the makeup gas froma PCM

1

Connect the tubing from the PCM to the 1 meter length of stainless steel
tubing from the kit with a union.

2

Connect the free end of the stainless steel tubing to the tubing from the
splitter assembly with a union. See

Figure 10

.

To supply the makeup gas from an Auxiliary Pressure controller

1

Install the brown-dot frit (part no. 19231-60610) in the output channel. See
your GC manual for details.

2

Connect the tubing from the Auxiliary Pressure controller to the tubing
from the splitter assembly with the 1/8 to 1/16-inch stainless steel reducing
union.

This completes the hardware installation.

Figure 10

Plumbing a PCM makeup supply

PCM

Union

Union

To splitter

Stainless

steel

tubing

«
...
22
23
24
25
26
...
»

Содержание G3180B





















































Отзывы:

Нет отзывов

Похожие инструкции для G3180B

Бренд: IB Connect Страницы: 2

Бренд: UNICOM Страницы: 9

Бренд: Clear-Com Страницы: 16

Бренд: MADRIX Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: Siemens Страницы: 6

Бренд: Siemens Страницы: 32

SIMATIC NET 6GK1901-0BE10-0AA0

Бренд: Siemens Страницы: 16

CAN-T-Connector

Бренд: ESD Страницы: 22

Бренд: Encore Страницы: 2

Бренд: Diablotek Страницы: 1

Бренд: RedLeaf Страницы: 3

Бренд: Rose electronics Страницы: 16

Бренд: Essential Audio Tools Страницы: 4

Бренд: Blonder tongue Страницы: 8

Бренд: Xantech Страницы: 5

Бренд: Acom Страницы: 9

Бренд: Hall Research Technologies Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды