manualshive.com logo in svg

Agilent Technologies G1531-67000, Инструкция по эксплуатации

Поделиться
Скачать
Agilent Technologies G1531-67000 Скачать руководство пользователя страница 1

Agilent Technologies

Agilent FID Maintenance Kit Instructions

For 7890, 7820, 6850, and 6890 Series GCs

Overview

This document contains instructions for two different FID 
Maintenance Kits.

Please review the whole document before starting the 
procedures.

Materials Required for FID Maintenance

•

One of the two maintenance kits listed in 

Table 1

.

•

The appropriate FID Jet for your configuration and 
application. See 

“Selecting a Replacement FID Jet” 

on page 2.

•

T20 Torx screwdriver.

•

1/4-inch nut driver.

•

Tweezers.

•

1/4 x 5/16-inch wrench.

•

7/16 x 9/16-inch wrench if adaptable FID.

Table 1

Available FID Maintenance Kits

Part Number

Description

Purpose

G1531-67000

FID Maintenance Kit for “

Cleaning

”

Contains

: Instructions, ignitor glow-plug, 

2 PTFE collector insulators, FID housing gasket, 

cleaning brushes, jet cleaning wire

Key parts are replaced, most are cleaned per 

the instructions provided. Jet and column 

adapter ordered separately. More labor 

intensive – about 1 hour labor.

G1531-67001

FID Maintenance Kit for “

Rebuilding

”

Contains

: Instructions and a complete FID 

collector assembly

The entire collector assembly including the 

ignitor is replaced.
The jet and column adapter must be ordered 

separately – about 15 minutes labor.

Содержание G1531-67000



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды