AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя

Страница: 62 / 74

BU-0101704 R3

c. Observe the end of the bin sweep around the bin and note the position in its revolution which has the

minimum clearance to the bin wall. This minimum clearance will later be used to adjust the sweep
extender.

d. Allow the end wheel to contact the sweep stop to ensure it prevents the sweep from advancing.

e. Using the sweep stop cable outside of the bin, lift up the sweep stop to ensure the end wheel will clear

it and perform a second pass.

7. After the bin sweep has completed its test-run, ensure the sweep is in its “start/park position” (directly over

the intermediate sumps), and then shut down and lock out bin unload system.

Failure to park the bin sweep over the intermediate sumps could result in damage to the
bin sweep when it is next operated.

8. Close all sump gates.

6.18. Adjust the Bin Sweep Extension

1. Remove the two 3/8” x 1” bolts and lock washers on the top of backboard extension (see

Figure 58

2. Move the extension outward to the same length as the minimum clearance between the end of the sweep

and the bin wall (and attached parts), as observed during the full test-run revolution. Pull and twist the
sweep flighting to extend it.

3. Re-fasten the bolts on the backboard extension.

Figure 58.

Adjust Bin Sweep Extension

6.19. Attach the Westeel Brand Logo Decal

1. Apply the brand logo decal to the pulley guard (see

Figure 59 on page 63

Important

Do not cover any existing safety or instruction decals with the brand logo decal.

2. Refer to

Section 2.8.1 – Decal Installation/Replacement on page 9

for specific instructions on applying

decals.

6. ASSEMBLY

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

Содержание Westeel EasyFlow2 100 Series











































































Результаты поиска

Содержание Westeel EasyFlow2 100 Series

Отзывы:

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренды по названию

Популярные бренды

AGI Westeel EasyFlow2 100 Series, Сборка и инструкция по установке

Результаты поиска

Содержание Westeel EasyFlow2 100 Series

Отзывы:

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренды по названию

Популярные бренды