manualshive.com logo in svg

AGI Westeel EasyFlow2 100 Series, Сборка и инструкция по установке

Поделиться
Скачать
AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя страница 61

BU-0101704 R3

61

6.17. Testing

1. Ensure that the power to the bin unload system is shut down and locked out.

2. Ensure that there are no obstructions in the sumps, sweep flighting, or sweep path along the bin floor.

3. Engage the gearbox by pulling the gearbox shift handle away from bin wall (see

Figure 57

).

Use the locking pin to lock the gearbox shift handle into the engaged or disengaged
position at all times. Failure to do so will result in damage to gearbox.

Figure 57.

Lower Gearbox Engagement & Disengagement for Sweep

4. Turn on power to bin unload system. The underfloor auger and sweep should both be rotating.

KEEP AWAY from rotating flighting. Do not perform adjustments on the equipment while it
is being tested.

5. Disengage the gearbox shift handle by pushing the handle toward the bin wall and ensure the lower gearbox

comes fully out of gear with no grinding (see

Figure 57

). Then shut down the bin unload system.

•

If grinding occurred when disengaging the gearbox shift handle: Lock out whole bin unload system.
Adjust the gearbox shift adjust tube as noted in the Maintenance chapter of the Operator’s Manual.

•

If grinding did not occur: With the unload system shut down, re-engage the gearbox. Restart the electric
powerhead so that underfloor auger flighting and sweep flighting are both rotating.

To prevent damage to the unload system, DO NOT engage bin sweep while underfloor
auger is operating.

6. Perform a test-run of the bin sweep (one full revolution around bin). During testing, check the general

function of the system and monitor the following:

a. Ensure that the bushings (between sweep sections) are not interfering with the sweep flighting.

b. Ensure sweep backboard does not catch on high spots on the aeration floor. If necessary, consult bin or

aeration floor assembly manual to level.

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

6. ASSEMBLY

Содержание Westeel EasyFlow2 100 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды