AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя

Страница: 27 / 74

BU-0101704 R3

Figure 8.

Locating the Bin Center

6.3. Install the Underfloor Auger

If you are installing the underfloor auger

before

completion of the sidewall and anchoring the bin to the

foundation:

• Move the underfloor auger into nearly its final position in the bin before the final sidewall tier is complete.

• Cut an opening in the appropriate bin sheet before the sheet is installed (see

Section 4.5 – Bin Wall Cutout

on page 20

• After the bin sidewall has been completed and anchored to the foundation, according to the principles given

Section 6.3.1 – Install by Removing the Bin Sheet on page 27

, perform final positioning and leveling of the

underfloor auger, installing the anchor legs, and anchoring the underfloor auger.

If you are installing the underfloor auger

after

anchoring the bin sidewall to the foundation, follow either

Section 6.3.1 – Install by Removing the Bin Sheet on page 27

Section 6.3.2 – Install by Cutting a Bin Sheet in

Place on page 29

according to the conditions given within those sections.

6.3.1 Install by Removing the Bin Sheet

This procedure describes removing a bin sheet after the bin sidewall has been anchored to the foundation and
applies to the installation of the underfloor auger

below the main door in a Westeel or Twister bin only

. You

must receive written permission from your bin manufacturer

if you want to use this procedure for:

• removing sidewall sheets other than below the main door for Westeel or Twister bins, or

• removing any sidewall sheets for bin manufacturers other than Westeel or Twister.

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

6. ASSEMBLY

Содержание Westeel EasyFlow2 100 Series











































































Результаты поиска

Содержание Westeel EasyFlow2 100 Series

Отзывы:

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренды по названию

Популярные бренды

AGI Westeel EasyFlow2 100 Series, Сборка и инструкция по установке

Результаты поиска

Содержание Westeel EasyFlow2 100 Series

Отзывы:

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренды по названию

Популярные бренды