background image

 

 

GENERAL 

The following disclaimers apply to the goods in all circumstances: 

I.

 

The goods must be installed by a certified installer recognized by local authorities, where applicable, and strictly 

in accordance with Westeel’s Installation Instructions  as well as all applicable installation and building codes and 

accepted trade practices.  Without  limiting  the  generality  of  the  foregoing,  proper  foundation  assembly, 

installation  and  use  solely  for  the  purposes  intended  as  specified  in  Westeel’s  published product literature 

is essential.  As well, tank venting for both normal and  emergency situations must be installed properly and kept 

unobstructed always. 

II.

 

The goods must be handled always (including but not limited to shipping, loading and unloading, positioning) 

only  when  empty and  must be  secured always in a manner as specified in the Owners’ Manual.  Any damage 

caused during  handling is not covered by the warranty. 

III.

 

Any  damage  caused  by  foreign  debris  entering  into  the  tanks,  including  but  not  limited to moisture, is not 

covered by the warranty.  It is extremely important for the  owner/user to check for foreign debris inside the tank 

at the time of delivery as well  as before commencing use of the goods and regularly during use of the goods. 

Moisture can  cause  irreparable  damage  to  the  goods  including  but  not  limited  to  a  leak due to microbial 

corrosion.  For further information on moisture monitoring and  removal you may contact: 

 

Steel Tank Institute (STI) 

 

Westeel website 

 

Petroleum Equipment Institute 

IV.

 

Accessories and parts on the goods may not have been manufactured by Westeel  (“third  party  manufactured 

goods”).  Third  party  manufactured  goods  are  not  covered by the warranty.  Warranty terms applicable to 

third-party manufactured  goods are as per the terms published by the  applicable manufacturer.  For further 

information on accessing the website of the applicable manufacturer please contact a  Westeel representative. 

V.

 

Modifications made to the  goods that have  not been approved in  writing by an authorized representative of 

Westeel will result in the warranty being null and void.  This will be the case for any and all damages howsoever 

caused to the goods at any  time after the modification has been made. 

VI.

 

The goods must be maintained and used at all times in a manner consistent with all  Westeel procedures contained 

in the Owners’ Manual as well as prudent, accepted  practice. 

 

Содержание FUEL-VAULT
















Отзывы: