AGI 15100SA Скачать руководство пользователя страница 41

Страница: 41 / 82

P1512161 R0

3.14. Install the Hydraulic Drive

Install the Motor Mount and Sprocket/Chain Assembly

1. Remove the 1/2" locknuts (2) from the drive roller flange bearing (7).

Note

These bolts will be used to fasten the motor mount (1) to the conveyor.

2. Install the square key (4) into the drive roller shaft. See

Figure 32

3. Loosely fasten the motor mount (1) to the drive roller flange bolts using the nuts removed in step 1.

4. Install the sprocket and chain assembly:

a. Assemble the 1" bore sprockets (3, 6) and chain (5) with the connector link.

b. Slide the sprocket and chain assembly onto the drive roller shaft.

Table 13.

Mount and Sprocket Components

Item

Description

Motor Mount

1/2" Nylock Nut (removed from bearing)

1" Bore Sprocket (5014 Half Thick)

1/4" x 1-1/2" Key

Chain Coupling (5014)

1–1/4" Bore Sprocket (5014 Half Thick)

Drive Roller Flange Bearing

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

3. ASSEMBLY

Содержание 15100SA



















































































Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды

AGI 15100SA, Инструкция по сборке

Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды