AGFA Avantra 36/44 Скачать руководство пользователя страница 401 | Manualshive

Страница: 401 / 521

AGFA Avantra 36/44 Скачать руководство пользователя страница 401

Avantra 36/44 Service Manual

2-8

Functional Analysis

2.3.3 The LUTH Motor Board (LMB)

The Luth Motor Board (LMB):

•

Amplifies the motor preset value to the corresponding high voltage to drive
the main motor.

•

Senses and limits the armature current.

•

Receives and converts I/R pulse preset values.

Description of Inputs and Outputs (P/N 52024000100)

•

X102 1, 2–24V AC input.

•

X102 5, 6–0-24 DC output.

•

X1 1, 2, 3–Optical interrupter.

•

X3 1, 2–Tacho feedback to CPU.

•

U201–Infrared receiver.

•

X4 1,2–Motor overload signal.

2.3.4 The Agfa Terminal Board (ATB)

The Agfa Terminal Board (ATB):

•

Displays convenient information

•

Organizes the output from activated keys

•

Organizes the input data

Description of Inputs and Outputs

1, 2–Data communication link between the LCB and the Agfa Terminal Board
(ATB). RS-232 serial data coded as ASCII characters are interchanged.

2.3.5 Sensors

•

Optical Interrupter–This device consists of a transmissive sensor with four
(4) wires and connectors. The operating wavelength is 950 nm. The detec-
tor is a Photologic IC with Schmitt-Trigger output. Aperature size is 0.5 mm.

•

Film Sensors (Input, Input/Output, Exit)–This sensor is an ultra low force
motion sensor. It features a long-life reed switch, an integral actuator arm,
and a magnet.

Operating Parameters:

Off point: Less than 10

°

rotation from rest position.

On point: Greater than 3

°

rotation from rest position.

•

Temperature Sensor–The sensitive element is a platinum-coated ceramic
wafer manufactured by thin film techniques. The exact value is obtained by
laser trimming.

«
...
399
400
401
402
403
...
»

Содержание Avantra 36/44










































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды