AGCO LELY ATTIS PT 130 Скачать руководство пользователя страница 44

Страница: 44 / 98

3.2 Connect the machine to the tractor

3.2.1 Connect the machine to the tractor

WARNING: Risk of sudden movement.

Always stop the engine and remove the ignition key when you exit the tractor.

WARNING: Risk of ejected high pressure oil.

The pressure of the tractor hydraulic system must not be more than 210 bar

Procedure
1.

Adjust the drawbar pull eye to make sure

that the wrapper table is level when you

connect the machine to the tractor.

GUID-4CD6D309-2B58-4545-8489-602307CD96B1-high.jpg [High]

Fig. 10

Use the suction device if applicable, and install the E-Link Basic controller in the tractor cabin.

NOTE:

If the length is incorrect, use the battery cable set.

Connect the power supply cable of the E-Link Basic controller to a 12V supply in the cabin.

Set the controller to the off position.

Align the tractor draw bar to the machines pull eye.

Release the pressure in the tractor hydraulic system.

Put the pin through the pull eye and lock it to

connect the machine behind the tractor.

GUID-A40E648C-FAA1-4EDF-A7A1-DCA36CEBB0FC-high.jpg [High]

Fig. 11

[V]

GUID-E2108A56-8C49-4E69-9AF9-CA367E692638 [V1]

3. Operation

Bale Wrapper

4820.LE.EN01

Содержание LELY ATTIS PT 130


































































































Результаты поиска

Содержание LELY ATTIS PT 130

Отзывы:

Бренды по названию

Популярные бренды

AGCO LELY ATTIS PT 130, Руководство оператора

Результаты поиска

Содержание LELY ATTIS PT 130

Отзывы:

Бренды по названию

Популярные бренды