AGCO LELY ATTIS PT 130 Скачать руководство пользователя страница 41

Страница: 41 / 98

3.1.4 Adjust the bearings adjust plate

Procedure
1.

Release the fasteners of the adjust plate (1)

and the roller bearings (2) on the right side of

the trailer.

Adjust plate

Roller bearings

16 mm

22 mm

28 mm

Correct roller belt tension

GUID-1224FE13-2233-4414-9D7D-F3E738498BB4-high.jpg [High]

Fig. 6

Turn the adjust plates (1) to the applicable

side (A), (B), (C) to give the correct tension

(D) on the roller belts.

Make sure that the adjustment keeps the

rollers parallel to each other.

Tighten the fasteners on the adjust plate (1).

Tighten the fasteners on the roller bearings

(2) against the adjust plate (1).

GUID-3F767870-1033-43A9-BE51-73AF7139C830-high.jpg [High]

Fig. 7

3.1.5 Adjust the film stretch

Procedure
1.

NOTE:

If there are two bolts in the gear box

cover then go to 3.1.6.

Remove the cover of the gear box (1).

Cover

Fastener

Washer

Gear wheel

Support

Remove the fastener (2) that holds the gear

wheels (4) and (5) on the cover (1) of the

gear box.

Remove the gear wheels (4) and (5) from the cover (1) of the gear box.

NOTE:

Make sure that the smallest gear wheel is nearest to the support

(8)

GUID-42E42CB1-DD4F-429A-BA20-C1B25AB462F2-high.jpg [High]

Fig. 8

GUID-8DFFD26C-8532-491A-AD58-5CDF890D3747 [V1]

GUID-AA334769-B561-4E8E-82E9-B0EA40FFE97F [V1]

3. Operation

Bale Wrapper

4820.LE.EN01

Содержание LELY ATTIS PT 130


































































































Результаты поиска

Содержание LELY ATTIS PT 130

Отзывы:

Бренды по названию

Популярные бренды

AGCO LELY ATTIS PT 130, Руководство оператора

Результаты поиска

Содержание LELY ATTIS PT 130

Отзывы:

Бренды по названию

Популярные бренды