manualshive.com logo in svg

AG SHIELD 12" CROSS AUGER, Руководство оператора

Поделиться
Скачать
AG SHIELD 12

 

7 

3. SAFETY 

 

SAFETY ALERT SYMBOL 

 
 

This Safety Alert symbol means: 

ATTENTION!  BECOME ALERT!  
YOUR SAFETY IS INVOLVED! 

 

The  Safety  Alert  symbol  identifies  important 
safety  messages  on  the  Ag  Shield  Cross  auger 
and  in  the  manual.  When  you  see  this  symbol, 
be  alert  to  the  possibility  of  personal  injury  or 
death.  Follow  the  instructions  in  the  safety 
message.

 

 

 
 
 
 
 
 
 
 
 
 

 
 
 

 

 
 
 
 

Accidents Disable and Kill

 

3 Big Reasons

 

Accidents Cost

 

 

Accidents Can Be Avoided

 

 
 
SIGNAL WORDS: 
 

Note the use of the signal words 

DANGER, WARNING 

and 

CAUTION

  with  the  safety  messages.  The 

appropriate  signal  word  for  each  message  has  been 
selected using the following guide-lines: 
 

 
 
 
 

 
  DANGER  - 

An  immediate  and  specific  hazard 

which  WILL  result  in  severe  personal 
injury or death if the proper precautions 
are not taken. 

  

WARNING  - 

A  specific  hazard  or  unsafe  practice 

which COULD result in severe personal 
injury or death if proper precautions are 
not taken. 

 

CAUTION -  

Unsafe  practices  which  COULD  result 
in personal injury if proper practices are 
not  taken,  or  as  a  reminder  of  good 
safety practices. 

 

Содержание 12" CROSS AUGER





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды