manualshive.com logo in svg

AFLOWT BUF M, Руководство по эксплуатации

Поделиться
Скачать
AFLOWT BUF M Скачать руководство пользователя страница 19

19 

 

3. INSTALLATION OF THE FLOW METER 

3.1. Transportation 

The flow meter must be transported to the installation site in its orig-

inal packaging. 

After transportation to the place of installation at a negative temper-

ature and introduction into the room with a positive temperature, the flow 
meter should be kept in the package at least 3 hours to avoid moisture 
condensation. 

When unpacking the flow meter, check its completeness in accord-

ance with the passport for this device. 

3.2. Installation requirements for the flow meter 

3.2.1. To install the device on the site it is necessary to have a free section in 

the pipeline for installation of the flow meter.  
The following conditions must be met at the CP installation site:  

-  Liquid  pressure  and  pipeline  operation  modes  exclude  gas  formation 

and/or accumulation of gas (air) 

- The internal volume of the CP must be filled with liquid during operation;  
- there are no or minimum pulsations and swirls of liquid. 

CP may be installed in horizontal, vertical or inclined piping (Fig.4). 

The CP (PEA) must not be located at the highest point of the pipe section. 
The most suitable place for installation, if any, is the upstream or down-
stream section of the pipeline. 

 

 Fig.4. Recommended installation locations for the CP of flow meter 

NOTE.  If  it  is  not  possible  to  install  the  flow  meter  in  the  recom-

mended places, it is possible to install the device at the top of the pipeline. 
It is necessary to install an air valve (air vent) at a point above the upper 
point of the flow meter, for example, in the expansion of the pipeline.  

WARNING:

 Ensure that the air valve is in good working order. Cor-

rect operation of the flow meter is possible only when there is no air in 
the duct. 

3.2.2. The difference between the inner diameters of the pipeline and the CP 

pipeline section at the jointing points must not exceed 0.05

·

DN. 

3.2.3. When installing the CP on a pipeline, it is recommended that the longitu-

dinal plane of PEA (the plane passing through a pair of PEA along the 

Содержание BUF M

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды