AFG N608 Скачать руководство пользователя страница 2

 

 

2015 AFG Baby Furniture N608 Assembly Sheet

 

WARNING:

 

READ ALL WARNING & SAFETY INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP 
INSTRUCTIONS WITH CRIB FOR FUTURE USE. 

First remove hardware from box and sort by size. Check to see that all hardware and wooden pieces 
are present before assembling. 
Follow instructions listed below in the proper sequence as numbered to assure fast, easy and correct 
assembly. 
DO NOT use this crib if the enclosed or attached instructions cannot be strictly adhered to. 
 

WARNING: 

  DO NOT attempt to repair or modify parts with cracks or defects.  Please contact us for immediate 

replacement. 

  This product is for home use and is not intended for use in schools, day care centers or other 

commercial establishments. 

  Must be assembled by a capable adult. 

 

CHOKING HAZARDS:

 DO NOT put small / loose components on top of the changing table unit 

where baby could reach. 

 

Crib Warnings 

WARNING

 

Failure to follow these warnings and the assembly instructions could result in serious injury or death. 

  This crib conforms to applicable regulations promulgated by the Consumer Products Safety 

Commission. 

  To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to 

sleep, unless otherwise advised by your physician. 

  DO NOT use a water mattress with this crib. 

  If refinishing, use a non-toxic finish specified for children’s products. 

  Check fasteners periodically and never over tighten then, as this may cause distortion or 

breakage. 

  Never use plastic shipping bags or other plastic film as mattress covers because they can cause 

suffocation. 

  CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 IN BY 51-5/8 IN 

(69CM X 131CM) WITH A THICKNESS THAT DOES NOT EXCEED 6 IN (15CM). THE 
MATTRESS USED WITH THIS CRIB SHOULD BE OF A LENGTH AND WIDTH SUCH THAT 
THE GAP BETWEEN THE MATTRESS AND THE SIDES OF THE CRIB DOES NOT EXCEED 
3CM (1.2 IN) WHEN THE MATTRESS IS PUSHED INTO ANY CORNER OF THE CRIB.  

  Never leave child unattended inside crib. Use this crib as a crib, not as a play yard. Remember 

that a crib is not a substitute for a parent’s supervision. 

  Parents should ensure a safe environment for their child by checking the crib regularly before 

placing the child in the products. Please make sure that every component is properly and securely 
in place. 

  When a child is able to pull to a standing position, set the mattress to the lowest position and 

remove bumper pads, large toys and other objects that could serve as steps for climbing out. 

  Infants can suffocate in gaps between crib sides and a mattress that is too small. 

  Follow warnings on all products in a crib. 

Содержание N608

























Отзывы: