aFe Power takeda 56-70043D Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 16

aFe Power takeda 56-70043D Скачать руководство пользователя страница 2

Page 2

•

Please read the entire instruction manual before proceeding.

• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7100.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Retain factory parts for future use.

Label Qty. Description

Part Number

A1

1

Air Filter (Pro 5R)

R24-90101

A2

1

Air Filter (Pro DRY S)

R21-90101

B

1

Tube 1 of 2

05-5670039B1

C

1

Tube 2 of 2

05-5670039B2

D

1

Housing

05-5670043B3

E

1

Coupling, Silicone Bellows: 2-

3/4”ID x 3”L

05-01656

F

1

Coupling, Silicone Hump: 2-

3/4”ID x 3”L

05-01501

G

4

Clamp 044

03-50019

H

2

Screw, Torx: M4

03-50491

J

1

Takeda Plug

05-01527

Installation will require the following tools:

Flat head screwdriver (or panel clip removal tool), #2 Philips screwdriver, T20 Torx driver, pliers, 10mm
wrench, 7mm, 8mm, and 10mm nut drivers.

Warranty Information available at

https://afepower.com/contact#warranty

Emissions Disclaimer:

This product is not currently CARB exempt and is not available for purchase in

California or for use on any vehicle registered with the California Department of Motor Vehicles.

«
1
2
3
4
...
»

Содержание takeda 56-70043D

















Отзывы:

Нет отзывов