Aerotech PRO225LM Series Скачать руководство пользователя страница 12

Страница: 12 / 54

Overview

PRO225LM Hardware Manual

PRO225LM Linear Motor Stage (continued)

Cable Management (Required)

-CMS0

No external CMS, motor/feedback connector bracket on carriage

-CMS1

External CMS for single axis

-CMS2

External CMS for lower-axis of two-axis PRO (XY) assembly

-CMS3

External CMS for lower-axis of two-axis (XZ or XT) assembly

-CMS4

External CMS for upper-axis of two-axis PRO (XY) assembly

-CMS5

External CMS for upper-axis of two-axis (YZ or YT) assembly

-CMS6

External CMS for lower-axis of three-axis (XYZ or XYT) assembly

-CMS7

External CMS for lower-axis of three-axis (XZT) assembly

-CMS8

External CMS for upper-axis of four-axis (XYZT) assembly

-CMS9

External CMS for lower-axis of four-axis (XYZT) assembly

Lifting Hardware (Optional)

-LF

Lifting hardware

NOTE:

Lifting option only available on travels 300 mm and greater. Lifting should never by ordered on the upper-axis of an XY set

(only order on lower-axis)

ThermoComp™ (Optional)

-TCMP

ThermoComp™ integrated thermal compensation unit, single or lower axis

NOTE

: An A3200 controller must be used with the -TCMP option

Metrology (Required)

-PL0

No metrology performance plots

-PL1

Metrology, uncalibrated with performance plots

-PL2

Metrology, calibrated (HALAR) with performance plots

Accessories (To be Ordered as a Separate Line Item)

ALIGN-NPA

Non-precision XY assembly

ALIGN-NPAZ

Non-precision XZ or YZ assembly

ALIGN-PA10

XY assembly; 10 arc sec orthogonality. Alignment to within 7 µm orthogonality for
short travel stages.

ALIGN-PA10Z

XZ or YZ assembly with L-bracket; 10 arc sec orthogonality. Alignment to within 10
µm orthogonality for short travel stages.

ALIGN-PA5

XY assembly; 5 arc sec orthogonality. Alignment to within 3 µm orthogonality for
short travel stages.

ALIGN-PA5Z

XZ or YZ assembly with L-bracket; 5 arc sec orthogonality. Alignment to within 5
µm orthogonality for short travel stages.

Chapter 1

www.aerotech.com

Содержание PRO225LM Series























































Результаты поиска

Содержание PRO225LM Series

Отзывы:

Похожие инструкции для PRO225LM Series

Бренды по названию

Популярные бренды

Aerotech PRO225LM Series, Руководство по оборудованию

Результаты поиска

Содержание PRO225LM Series

Отзывы:

Похожие инструкции для PRO225LM Series

Бренды по названию

Популярные бренды