Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 114

background image

76

Chapter 3

www.aerotech.com

3.1. Relay Connector (TB301)

The relay can be used to automatically control a fail-safe brake on a vertical axis. It can also be used as a
general purpose relay. The normally-open relay contacts are accessible through TB301 and the Motor
Feedback connector. The normally-closed relay contact is only accessible through TB301 (

). The

Motor Feedback connector allows the brake wires to be included in the motor feedback cable and eliminate
the need for a separate brake cable.

The brake output can be software configured; refer to the A3200 Help file for more information (see topics for
the EnableBrakeControl parameter and the BRAKE command).

When TB301 is used to power the mechanical brake control relay, the solid state brake control relay (TB202)
should not be used.

The user must verify that the application will be within the specifications of the Brake/Relay contacts.

Table 3-3:

Voltage and Current Specifications (TB301)

Relay K1 Contact Ratings

Maximum Switched Voltage

150 VDC, 125 VAC

Maximum Switched Current

1A

Maximum Carrying Current

1A

Maximum Switched Power

30 W (DC), 60 VA (AC)

N O T E :

Do not exceed Maximum Current or Maximum Power specifications.

Table 3-4:

Relay Connector Pinout (TB301)

Pin#

Description

In/Out/Bi

1

Brake Relay Output Normally Closed Contact

Output

2

Brake Relay Output Common Contact

Output

3

Brake Relay Output Normally Open Contact

(1)

Output

(1) For JP3 jumper configuration, refer to

Table 3-5:

Mating Connector Part Numbers for the Relay Connector (TB301)

Description

Aerotech P/N

Phoenix P/N

Wire Size:

AWG [mm

2

]

3-Pin Terminal Block

ECK01449

1881338

0.5 - 0.080 [20-28]

The configuration of JP3 (

) allows either the Brake + or the Brake - output to be switched by the

relay and connected at the Motor Feedback connector or for the brake to be connected at TB301. Refer to

for more information.

Table 3-6:

-IO Expansion Board Brake Jumper Configuration

Jumper

Setting

Description

JP2

1-2

PSO Output Active High, Low Z during reset

2-3

(1)

PSO Output Active Low, High Z during reset

JP3

1-2, 3-4

Switch Brake +

5-6, 7-8

(1)

Switch Brake -

1-3

Relay Only

(1) default

Ndrive HPe 50/75/100

-IO Expansion Board

«
...
74
75
76
77
78
...
»

Содержание Ndrive HPe 100



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ndrive HPe 100

Compax3 Fluid T40

Бренд: Parker Страницы: 398

Бренд: Wittenstein Alpha Страницы: 22

Megatorque M-EDC-PN2012 Series

Бренд: NSK Страницы: 32

Бренд: Omron Страницы: 8

Бренд: Parker Страницы: 54

Бренд: gefran Страницы: 40

Бренд: CENTENT Страницы: 36

Бренд: TELUS Страницы: 49

Бренд: SSD Drives Страницы: 319

GIN-SAC4 Series

Бренд: Indel Страницы: 94

ELTRAL KS 30/40 Remote

Бренд: G-U Страницы: 16

ELTRAL KS 30/40 RADIO CONTROL

Бренд: G-U Страницы: 20

Бренд: G-U Страницы: 24

SUBDRIVE CONNECT PLUS

Бренд: Franklin Electric Страницы: 56

Бренд: Coolmay Страницы: 99

Бренд: Apricorn Страницы: 18

Бренд: Wheeler-Rex Страницы: 30

Бренд: LS Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды