Aerotech Automation1 XR3 Series Скачать руководство пользователя страница 34

Страница: 34 / 104

2.2. Motor Power Output Connector

DANGER

: Before you do maintenance to the equipment, disconnect the electrical power.

Wait at least ten (10) minutes after removing the power supply before doing maintenance
or an inspection. Otherwise, there is the danger of electric shock.

The XR3 can be used to drive the following motor types:

Brushless (refer to

Section 2.2.1.

)

DC Brush (refer to

Section 2.2.2.

)

Stepper (refer to

Section 2.2.3.

)

For a complete list of electrical specifications, refer to

Section 1.1.

IMPORTANT

: Refer to local electrical safety requirements to correctly size external system

wires.

The 5-pin high power “D” style motor power connectors (Axis 1-6) are located on the rear panel. The pin
assignments for these connectors are shown in

Table 2-4

Table 2-4:

Motor Power Output Connector Pinout

Pin

Description

Recommended

Wire Size

Connector

Ground

1.3 mm

(#16 AWG)

Reserved

1.3 mm

(#16 AWG)

Brushless Phase C Motor Power
DC Brush -
Stepper Return

1.3 mm

(#16 AWG)

Brushless Phase B Motor Power
Stepper

1.3 mm

(#16 AWG)

Brushless Phase A Motor Power
DC Brush +
Stepper

1.3 mm

(#16 AWG)

Table 2-5:

Mating Connector Part Numbers for the Motor Power Output Connector

Description

Aerotech P/N

Third Party Source P/N

Male 5 Pin D-Style

ECK01236

ITT Cannon DBM5W5PK87

Contact (QTY. 5)

ECK00660

ITT Cannon DM53745-7

Backshell

ECK00656

Amphenol 17-1726-2

2.2. Motor Power Output Connector

XR3 Hardware Manual

www.aerotech.com

Содержание Automation1 XR3 Series









































































































Результаты поиска

Содержание Automation1 XR3 Series

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Automation1 XR3 Series, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XR3 Series

Отзывы:

Бренды по названию

Популярные бренды