manualshive.com logo in svg

Aerotech Automation1 XR3 Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XR3 Series Скачать руководство пользователя страница 38

2.2.2. DC Brush Motor Connections

The configuration shown in

Figure 2-7

is an example of a typical DC brush motor connection. Refer to

Section 2.2.2.1.

for information on motor phasing.

Figure 2-7:

DC Brush Motor Configuration

2.2.2.1. DC Brush Motor Phasing

A properly phased motor means that the positive motor lead should be connected to the ØA motor
terminal and the negative motor lead should be connected to the ØC motor terminal. To determine if
the motor is properly phased, connect a voltmeter to the motor leads of an un-powered motor:

1. Connect the positive lead of the voltmeter to the one of the motor terminals.
2. Connect the negative lead of the voltmeter to the other motor terminal.
3. Move or rotate the motor in the positive or clockwise (CW) direction by hand.

Figure 2-8:

Positive Motor Direction

4. If the voltmeter indicates a negative value, swap the motor leads and move the motor by hand in

the positive direction, again. When the voltmeter indicates a positive value, the motor leads have
been identified.

5. Connect the motor lead from the positive lead of the voltmeter to the ØA motor terminal on the

XR3. Connect the motor lead from the negative lead of the voltmeter to the ØC motor terminal
on the XR3.

For Aerotech-supplied systems, the motor, encoder and Hall sensors are correctly configured and
connection adjustments are not necessary.

2.2.2. DC Brush Motor Connections

XR3 Hardware Manual

38

www.aerotech.com

Содержание Automation1 XR3 Series









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды