manualshive.com logo in svg

Aerotech Automation1 XC6e Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC6e Series Скачать руководство пользователя страница 30

2.1.3. Minimizing Noise for EMC/CE Compliance

IMPORTANT

: The XC6e is a component designed to be integrated with other electronics.

EMC testing must be conducted on the final product configuration.

To reduce electrical noise, observe the following motor feedback and input power wiring techniques.

1. Use shielded cable for motor and feedback connectors. Connect the shield to the backshell at

each end of the cable.

2. Separate motor and power wiring from encoder and I/O wiring.
3. Mount drives, power supplies, and filter components on a conductive panel. Mount line filters

close to the drive to keep the wire length between the drive and filter to a minimum. Use an AC
line filter on the Control Supply such as Schaffner FN2010-6-06 or Corcom 10VW1 or similar. Use
an AC line filter on the Motor Supply such as a Schaffner FN258-55-34.

4. Use a separate wire for each ground connection to the drive.Use the shortest possible wire

length.

The following additional changes could be required for EMC compliance and are recommended during
initial EMC system evaluation.

1. Add a clamp-on ferrite to the feedback cable close to the drive.

[Aerotech PN ECZ02348, Fair-rite PN 0446167281]

2. Add a clamp-on ferrite to the Control Supply wires, including the ground wire, close to the drive.

[Aerotech PN ECZ02347, Fair-rite PN 0446164281]

2.1.3. Minimizing Noise for EMC/CE Compliance

XC6e Hardware Manual

30

www.aerotech.com

Содержание Automation1 XC6e Series















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды