background image

10 

 

5. With the nailer off the workpiece, pull the trigger. Depress the push lever against the workpiece. 

 

THE NAILER MUST OPERATE. 

6. If no abnormal operation is observed, you may load nails in the nailer. Drive nails into a test piece that is the 

same type of material that will be used in the actual application. 

 

THE NAILER MUST OPERATE PROPERLY. 

 

 

Firing modes

 

The  Air-powered  Coiled  Siding  Nailer  has  two  firing  modes:  sequential  fire  for  single  firing,  or  bump  fire  for 

repetitive, fast firing of nails. The bump fire trigger kit comes installed on the nailer, and the sequential fire trigger 

kit is included as replacement parts. See instructions on how to change from one mode to the other. 

 

METHODS OF OPERATION 

This  nailer  is  equipped  with  a  push  lever  at  the  nailing  point  and  will  not  operate  unless  the  push  lever  is 

depressed (pushed upwards). Each mode requires a different method of operation: 

1. Sequential fire (single shot) 

Position the nail outlet on the workpiece   

with finger off the trigger. 

Push the nailer down until the push lever   

is completely depressed. 

Pull the trigger to drive a nail. 

Remove finger from the trigger. 

To drive another nail, move the nailer along the 

  workpiece, repeating steps 1 to 4 as required. 

 

 

 

 

 

 

2. Bump fire (multiple shots) 

  Pull the trigger with the nailer off the workpiece. 

  Drive a nail by pressing the nailer against the   

workpiece to depress the push lever. 

  Drive additional nails by moving the nailer along   

the workpiece with a bouncing motion. Each   

depression of the push lever will drive a nail.   

When the required nails have been driven,   

remove finger from the trigger.   

 

WARNING!

 

    Potential hazard that may result in moderate injury or damage to equipment. 

●Keep your finger off the trigger except during fastening operation, because serious injury could result if the push 

lever accidentally contacts you or others in work area.   

●Keep hands and body away from the discharge area. The nailer with contact trip mechanism may bounce from 

the recoil of driving a fastener and unwanted subsequent fastener may be driven, possibly causing injury.   

●Some types of loaded nails can spark out of the muzzle during a nail driving operation. Exericise caution! 

 

 

 

Содержание CN65RA

















Отзывы: