background image

 

AEROMOTIVE  

Part # 17147 & 17148 

86-93 Mustang 5.0L Stealth Fuel System Kit 

 INSTALLATION INSTRUCTIONS 

 

CAUTION: 

Installation  of  this  product  requires  detailed  knowledge  of  automotive  systems  and 

repair  procedures.  We  recommend  that  this  installation  be  carried  out  by  a  qualified 
automotive technician. 

Installation  of  this  product  requires  handling  of  gasoline.  Ensure  you  are working in  a 

well  ventilated  area  with  an  approved  fire  extinguisher  nearby.  Extinguish  all  open  flames, 
prohibit  smoking  and  eliminate  all  sources  of  ignition  in  the  area  of  the  vehicle  before 
proceeding with the installation. 

When  installing  this  product,  wear  eye  goggles  and  other  safety  apparel  as  needed  to 

protect yourself from debris and sprayed gasoline

.

 

 

WARNING! 

The fuel system is under pressure. Do not open the fuel system until the pressure has 

been  relieved.  Refer  to  the  appropriate  vehicle  service  manual  for  the  procedure  and 
precautions for relieving the fuel system pressure

Aeromotive system components are not legal for sale or use on emission controlled motor vehicles. 
 

 

 
Warning – The included Aeromotive fuel pump is not compatible with alcohol based fuels or 

fuel additives! 

 
The following steps are typical of most installations: 

 
Section 1 - Fuel Tank Installation 
 
Section 2 – Fuel Rail Installation 
 
Section 3 – Fuel Regulator Installation and Fuel Line Plumbing 
 
Section 4 – Fuel Line Hose End Installation 
 
Section 5 – Electrical Installation 
 
Section 6 – Final Checks and System Start-up 
 
Section 7 – Filter Maintenance 
 
 

 

 

Содержание 17147














Отзывы: