Aeris F11, Руководство по эксплуатации

Страница: 15 / 36

15
F11 OPERATING MANUAL
© 2002 Design, 2013 Doc. No. 12-7285-r01 (5/3/13)
FREE CDT (COUNTDOWN TIMER)
The FREE Mode CDT (which is not the same one as the Watch CDT) counts down time values in minutes:seconds.
Unless it is set Off, it is displayed on the Surface Main and if a dive is started it will be displayed on the Dive Main.
When set for Auto, the countdown will keep repeating after counting down to 0:00 until stopped by S (< 2 sec).
CDT Lead-in,
information includes (Fig. 24):
> Graphics Go To and Cdt with icon.
• S (< 2 sec) - to access CDT Setup.
• A (< 2 sec) - to step forward to Set Alarms Lead-in.
• M (< 2 sec) - to step back to SURF ALT 2.
• M (2 sec), or 2 minutes of no button action, will revert to SURF MAIN.
• L (< 2 sec) - to toggle the Backlight On/Off.
Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
CDT Setup,
information includes (Fig. 25A/B/C):
> Countdown Time (min:sec) as >>
0:00 if no time has been set, or it completed the countdown; or -
min:sec set if Off (or Auto) and ready to start; or -
min:sec remaining if On (or Auto) with a countdown in progress.
> Graphic Cdt.
> Graphic OFF (or ON, or Auto) flashing (Fig. 25A).
• A (< 2 sec) - to step forward through selections of OFF, ON, AUTO (Fig. 25B), and SET (Fig. 25C).
• M (< 2 sec) - to step back through the selections.
• S (< 2 sec) - to save the selection.
>> If OFF, ON, or AUTO is selected, operation reverts to the Lead-in screen.
>> If SET is selected, the Set CDT screen is displayed.
• S (2 sec) - to revert to CDT Lead-in, if no setting change.
• M (2 sec), or 2 minutes of no button action, will revert to SURF MAIN.
• L (< 2 sec) - to toggle the Backlight On/Off. Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
Set CDT, information includes (Fig. 26):
> Timer setting (min:sec) with icons, with Minute digits flashing.
> Graphics Cdt and SEt.
• A (hold) - to scroll upward through Minute set points (8/sec) from 0: to 59: in increments of 1: (min).
• A (< 2 sec) - to step upward through Minute set points.
• M (< 2 sec) - to step back through set points.
• S (< 2 sec) - to save the Minute setting and flash the Seconds digits.
• A (hold) - to scroll upward through Seconds set points (8/sec) from :00* to :59 in increments of :01 (sec).
*Starts at :30 (sec) minimum when Minutes are set for 0: (min).
• A (< 2 sec) - to step upward through Seconds set points.
• M (< 2 sec) - to step back through set points one at a time.
• S (< 2 sec) - to save the CDT setting and revert to the CDT Status screen with SEt flashing, allowing ON or OFF to be selected
as previously described.
• S (2 sec) - to revert to CDT Setup, if no setting change.
• M (2 sec), or 2 minutes of no button action, will revert to SURF MAIN.
• L (< 2 sec) - to toggle the Backlight On/Off. Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
------------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------------------------------------------
Fig.24 - CDT LEAD-IN
Fig. 25A - CDT SETUP
(upon access)
or OFF
Fig. 25C - CDT SETUP
(to access Set)
Fig. 26 - SET CDT
Fig. 25B - CDT SETUP
(upon access)