AER domino 3, Руководство пользователя

Страница: 14 / 18

6. Technical data
Inputs, channels 1 – 4 (notes 1, 2)
Combo socket, XLR + jack ¼” (6.35 mm)
Line mode
High impedance, unbalanced jack input for
instruments (pick-ups) and line-level sources
Sensitivity:
26 mV (–32 dBV)
Pad switch (attenuator): –10 dB
Impedance: 1 Meg
Equivalent input noise,
A-weighted:
1.6 µV (–116 dBV)
Phantom power: +9 V DC at ring of jack sockets in
Ch. 1 and Ch. 3, switchable per channel (note 4),
max. 100 mA (all channels total), overload protected
Mic mode XLR (balanced), stereo jack (balanced),
or mono jack (unbalanced) input
Sensitivity:
7.5 mV (–43 dBV)
Pad switch (attenuator): –19 dB
Impedance (balanced): 1.7 k
Equivalent input noise,
A-weighted:
0.3 µV (–130 dBV)
Voice filter: –4 dB at 450 Hz (referred to 10 kHz)
Phantom power:
48 V, with common on/off
switch for all four channels (note 4)
Clip indicator : Headroom 6 dB
Return Stereo return from external parallel effect loop
2 x mono jack, ¼” (6.35 mm, left/right)
Sensitivity:
375 mV
Routing: stereo to speakers, headphones, rec out,
and L/R-out; mono (L+R) to DI out
Aux in
Auxiliary stereo input (e.g., for CD player)
Level adjustable
Cinch (RCA) sockets (left/right)
Sensitivity:
375 mV
Routing: stereo to speakers, headphones, rec out,
and L/R out; mono (L+R) to DI out
Outputs (note 3)
Tuner
Tuner output, not affected by mute switch
Mono jack, ¼” (6.35 mm)
Output voltage:
360 mV
Headphones
output.
When connected, internal speakers are muted.
Stereo jack, ¼” (6.35 mm)
Output power: max. 2 x 100 mW / 32 ohms
Input sensitivity for 2 x 50 mW / 32 ohms:
30 mV at line input (any channel)
Caution: For stereo headphones with stereo jack
plug only. Do not connect mono plu gs.
Active speaker Mono (L+R) output post-master, suitable for
active extension speaker
Mono jack, ¼” (6.35 mm)
Output voltage:
1.4 V
Activates 100 Hz low-cut filter for internal speaker
if plugged in.
L/R-out Stereo line output after tone controls,
with aux in and effectsLevel adjustable by pre out
2 x mono jack, ¼” (6.35 mm, left/right)
Output voltage:
0…1.4 V
Rec out Recording output after tone controls,
with aux in and effects
Cinch (RCA) sockets (left/right)
Output voltage: 1.4 V (note 4)
DI
Balanced XLR output before master, after tone
controls, with aux in and effects (note 4)
Level adjustable
Output voltage:
0…145 mV
Send
Send for parallel effect loop
Mono jack, ¼” (6.35 mm)
Output voltage:
710 mV (note 4)
USB lamp
DC output for a lamp
Data lines are not connected.
Output voltage:
5 V DC, max. 200 mA
Insert points
Insert L/R
Stereo insert point after master volume
2 x stereo jack (L/R), ¼” (6.35 mm)
Tip = send, ring = return
Output voltage:
1.4 V
Tone controls (all channels)
colour
+10 dB at 8 kHz, –3 dB at 700 Hz
bass ±8 dB at 100 Hz, shelf type
middle ±4 dB at 650 Hz
treble ±9 dB at 10 kHz, shelf type
Effects
Internal effect
AER 32-bit digital effect processor
with 16 factory presets
Two independent, simultaneous effects (one for
channels 1 and 2, and one for channels 3 and 4).
USB interface and PC software for creating user-
defined settings
External effect Parallel effect loop (see send and return)
Power amp 2 x 100 W / 4 ohms,
discrete bipolar transistor design
Dynamic range: 100 dB (A-weighted, see note 2)
Limiter threshold 2 x 85 W
Analog signal subsonic filter, low distortion RMS limiter
processing
Speaker system
Two 8” (200 mm) twin cone full-range speakers,
bass reflex enclosure
Mains power
Mains voltage (depending on model):
100, 120, 230, or 240 V AC, 50–60 Hz.
Power consumption:
max. 420 W
Mains fuse 5 x 20 mm
Slow 3.15 A for 230 and 240 V models
Slow 6.3 A for 100 and 120 V models
General
Cabinet
15 mm (0.6”) finnish birch plywood
Finish Waterbased acrylic, black spatter finish
Dimensions
Height : 365 mm (14.37“)
Width: 420 mm (16.54“)
Depth: 300 mm (11.81“)
Weight 16 kg (35.3 lbs)
16