Aeon Cobra 220 Скачать руководство пользователя страница 99

Страница: 99 / 105

11.9 HEADLIGHT LAMP REPLACEMENT

NOTE:

Allow lamp to cool before proceeding. Do

not touch a halogen lamp with bare fingers. Oil from

your skin leaves a residue, causing a hot spot which

will shorten the life of the lamp. Hold the bulb by the

base only.

To access the headlight assembly without removing

the front cover, reach up under the front cab.

Rotate the socket (2) counterclockwise and pull it

away from the headlight assembly.

Install the new headlamp.

Reinstall all components.

TAILLIGHT/BRAKELIGHT LAMP
REPLACEMENT

If the taillight/brakelight does not work the

lamp may need to be replaced.

(Step 1)From the rear of the taillight

remove two screws (1) holding lens

cover in place and remove lens cover.

(Step 2)Remove lamp (2) and replace it

with recommended lamp.

Reinstall the lens cover removed in Step 1.

Test the taillight/brakelight.

Содержание Cobra 220










































































































Результаты поиска

Содержание Cobra 220

Отзывы:

Бренды по названию

Популярные бренды

Aeon Cobra 220, Руководство по обслуживанию

Результаты поиска

Содержание Cobra 220

Отзывы:

Бренды по названию

Популярные бренды